Note:hand written solution should be avoided. Sample Problem 2.7Find the viscosity of the Newtonian liquid whose shear stress-shear rate curve is given in Fig. 2.33.t, dyne /em?OFO 01● 0.1 0.2 0.3 0.4dv/dt. 1/secFigure 2.33 Figure for sample problem 2.7Solution:Sincedy/dt the slope of the curve given in Fig. 2.33represents the viscosity.Slope30dyne/cm²0.33/sec90.9 poises.

A Figure that contains all necessary dataneed to find the viscosity of Newtonian fluid

Answered: Find the viscosity of the Newtonian…

Find the viscosity of the Newtonian liquid whose shear stress- shear rate curve is given in Fig. 2.33. 1, dyne /cm² 10 01 02 03 04 05 06 dwidt. 1/sec

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What are the two classes of adhesives?

A: Adhesives are defined as the material that is used to connect, join or stick two different objects.…

Q: Discuss in detail Kennedy and Lacey Theory? Write down all the design steps.

Q: Define coefficient of volumetric expansion.

A: The coefficient of volumetric expansion is defined as the ratio change in volume with respect to the…

Q: What is LAP SPLICING? Illustrate a figure and explain it thoroughly

A: A lap is when two pieces of reinforcing bar (rebar) are overlapped to create a continuous line of…

Q: List 15 types of construction materials

A: Following are the types of construction materials

Q: metallurgy slag is used in road construction to make roads better

A: Millions of tons of metallurgical slags are produced every year from several types of furnace during…

Q: Stability (one word): Blank 1 Determinacy (two-words); Blank 2 to the Blank 3 degree Blank 1 Blank 2…

Q: What is layerd cake

A: Layered cake:

Q: Using online information, write a one-page, double-spaced article on the useof fiber-reinforced…

A: Fiber reinforced plastic is also known as fiber reinforced polymer. It is a composite material made…

Q: Civil Engineering How does prefabrication contribute to construction operations? (For BIM) Ple

A: Introduction- Building design and construction management are increasingly relying on prefabrication…

Q: Is Graphene Coating In Construction a specific Product , Process or System? Also tell the objectives…

A: Concept- Carbon is the main component of graphene. With the use of graphene, a composite material…

Q: ASTM C188 Give three significance and uses of ASTM C188

A: ASTM - American Society for Testing and Materials. The code ASTM C 188 is used to determine the…

Q: exactly is the Taser solution?

A: Taser Solution is the way or innovations refers to the shocks that will comes from the weapons which…

Q: A W12x96 is loaded as shown. Find the maximum stress at point A (mid - height of

A: Column W12x96Area = 28.2 inch2Moment of inertia about the strong axis (Ix): 983 in4 (from steel…

Q: Mention 11 natural fiber ropes

A: Natural fiber rope refers to a type of rope which are made from plant-based materials. These ropes…

Q: 1. If the figure below is frictionless along the 9ft long surface, what is the velocity of the body…

Q: 6.2 THE FOLLOWING PROVISIONS IN A CONSTRUCTION CONTRACT ARE UNENFORCEABLE: CHECK ALL CORRECT…

A: UNENFORCEABLE means the clause in a contract that cannot be legally upheld by lawIt means if one…

Q: Step 5 incomprehensiable

A: In the step 5Settlement can be calculated using as below

Q: GENERAL INSTRUCTIONS: Answer the following questions comprehensively and neatly. FILE. History of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: How is Silica gel manufactured?

A: Silica Gel is a non-crystalline form of highly porous silica which is used for the following…

Q: what is grain elasticity?

A: Grit is the name for what is on a grinding, sanding or polishing tool. It is made up of a hard…

Q: 10) In case of architectural restrictions, the designer must: A) Place the rebars periodically B)…

A: Warning is being given before answering, However I do my best. I try to give good explanation…

Q: What does ASD stand for?

A: To define ASD and Its specifications.

Q: Differentiate between elasticity and plasticity.

A: Elasticity: Elasticity is the property of a material which regains it's original shape once the…

Q: Define Electro-osmosis.

A: Electro-osmosis:

Q: = What is the gage pressure [in psi]... Water Air Oil (SG=0.8)

A: Given:Required:Gage pressure at bottom of tankGage pressure in the air zone in the container

Q: Identify the properties of materials that must be considered when specifying construction products.

A: The properties of materials that must be considered are following:

Q: FORMWORKS 2) Give one alternative material/system to wooden forms (plywood/phenolic and lumber…

A: Steel formwork is an alternative material/system as replacement for formworks systems for structural…

Q: 20ド Sm 10m

Q: Explain the relationship between permeability and Darcy's law. Difference between particle specific…

A: Permeability : The ability of soil to permit water to flow through it is called to as permeability.…

Q: Determine the factor of safety of the slope shown in the figure below using an ESA and a TSA. The…

Q: explain how to avoid voids during concrete pouring

A: we have to asked how to avoid voids during concrete pouring

Q: ate unnecessary 6.2 A basic principle of et words. The following writing samples were taken from…

A: We are authorized to answer three subparts at a time since you have mentioned which part you are…

Q: Do plumbing fixtures weaken the strength of a component where it is built inside

A: A plumbing fixture is any plumbing component, such as a faucet, that has a specified usage and…

Q: What is negative skin friction ?

A: Friction is the resistance to motion of one object moving relative to another. It is not a…

Q: lap splicing

A: A lap splice is when two pieces of rebar overlap to form a continuous reinforcement. This helps…

Q: What’s the meaning of EDMI?

A: EDMI is nothing but the Electronic Distance Measuring Instrument which is used to measure the…

Q: identify and describe the importance in construction of conducting the following ASTM procedure…

A: Concrete temperature test The temperature of fresh concrete may be measured using ASTM C1064 to…

Q: Accuracy and Precision for all the following can not determine the accuracy of measurments can not…

Q: ce of making and curing concrete specimen i

A: Curing is a process during which a chemical reaction (such as polymerization) or physical action…

Q: Explain Bituminous Mix Design By Marshall Method. Write in your own words,i dont need copy paste…

A: Marshall Mix Design- This design determines the optimum bitumen content for the evaluation of…

Concept explainers

MATLAB

MATLAB software is a registered trademark, multi-model programming language, and numerical computing environmental system created by MathWorks. 'MATLAB' is the short-form of "Matrix Laboratory". The MATLAB software permits the utilization of matrix operations, graphical representation of data, execution of algorithms, development of user interface, and linking programs created in other languages. Even though MATLAB is developed mainly for numerical computing, there is an optional toolbox that uses a symbolic engine known as MuPAD giving access to all the symbolic computing abilities. In addition to this, a Simulink package delivers graphical multi-domain simulation and design that is model-based for embedded and dynamic systems. MATLAB users are spread worldwide across the world and use MATLAB extensively.

Question

Note:hand written solution should be avoided.

Sample Problem 2.7
Find the viscosity of the Newtonian liquid whose shear stress-
shear rate curve is given in Fig. 2.33.
t, dyne /em?
OFO 01
● 0.1 0.2 0.3 0.4
dv/dt. 1/sec
Figure 2.33 Figure for sample problem 2.7
Solution:
Since
dy/dt the slope of the curve given in Fig. 2.33
represents the viscosity.
Slope
30dyne/cm²
0.33/sec
90.9 poises.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

VIEW

Step 2: Introduction

VIEW

Step 3: calculation of viscosity

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Write any four different types of lubricants?
Discuss STRUCTURAL SAFETY.
civil engg material
The web thickness of lightest WT shape is?
Identify at least three wood products (with images) used in the construction industry and discuss its use and properties.
A. Briefly discuss the different types of tensile structures. B,Compare the two tensile solutions for the exhibition space roof. C. Choose one of the tensile structures solution from above and justify your selection Answer All Questions, Answer should be in typed format not in handwritten
Describe the various types of printer paper, such as matte, glossy, and specialty papers, and their ideal use cases.
1) What is the relation of steel and iron? 2) how iron entered the construction world in history, how the process went on, and why the major structural metal is steel in contemporary architecture? Please type answer required, take any reference Thank you, I will give rating
Discuss the advantages and disadvantages of using concrete, steel and timber in mild weather regions. Use perfect academic writing and academic references. Insert the links of academic reference Use perfect academic writing and academic references. Cite the information then Insert the links of academic reference is (((Necessary))). If you are copy the answer, I will give you down vote
7 Materials used for ceiling design enumerate how to install them and its considerations and how to maintain them
Who introduced the first EDM instrument and what was the name of that instrument?
Using examples of how the concept or system has been used or can be used in buildings (new construction and retrofits) Subject is smart windows