Find the velocity of flow in pipe in m/s.

Q: Two chambers, Chamber 1 and Chamber 2 where pressure at chamber 1 p1=70 kPa, at chamber 2 the…

A: To determine the actual flow rate through the orifice

Q: You wash your roof with a water hose at a height of 8.0 m above the ground. You connect two garden…

A: Given- P1 = Atmospheric pressure = 1.01 x 105 Pa v1 = 6 m/s height from datum 2 to 1 = (h) = 8 m By…

Q: The table shows head, discharge and efficiency of a centrifugal pump running at a constant speed of…

A:

Q: QI: If the overall efficiency of the system and turbine in the figure below is 80 percent. What…

A: Solution:

Q: A positive displacement pump has a capacity of 8 cm3 per revolution and runs at 1000 rpm. Its…

A: Given: N - 1000 rpm v - 8 cm3/rev nv - 0.89  K - 2.4 x 104 bar p - 1 bar/s V - 500 L To find :…

Q: Inlet and throat diameters of a horizontal venturimeter are 350 mm and 150mm respectively. The…

A:

Q: Q.2) As shown in the figure, gasoline (p=701 kg/m3, µ=0.51x10-3 N.s/m2) will be extracted from a…

A:

Q: Q3/ The horizontal pump in Fig. below discharges 20°C water Neglecting losses, what power in kW is…

A: GIVEN:discharge fromthe pump Q=57m3/h

Q: Parvinbhai

A: The objective of the question is to calculate the maximum torque that a hydraulic motor can generate…

Q: to the atmosphere. Estimate the pump power in kW delivered to the water.

A:

Q: A water truck drives slowly around a construction site, spraying water to keep dust down. A pump…

A:

Q: 1. For a hydraulic motor, its displacement Vp-250ml/r, the inlet and outlet pressure are 9.8MPa and…

A: Given: The displacement of the motor: →VP=250 ml/r=0.25×10-3 m3/r Inlet pressure→Pi=0.49 MPa Outlet…

Q: Water @ 30C and 1atm is flows at a rate of 0.5 m^3/s through a horizontal junction in a pipe. The…

A: To find: The resultant force on the junction. Given: The flow rate is Q=0.5 m3sec. The internal…

Q: A turbine is to be built in the south of Jordan for electrical power plant station. As a consultant…

A: Given,

Q: At a point A in a pipe line carrying water, the diameter is 1 m, the pressure is 98 KPa and the…

A:

Q: The average volume flow rate and the head of a hydropower station are 1110 m/s and 367 m,…

A:

Q: ter is 1025 kg/m³. Calculate (a) the quantity of water flowing through each A tidal km. The…

A: The given problem relates to power generation through tidal energy. There are 140 generators which…

Q: A pipe equipped with a nozzle is used to deliver water to the wheel of a hy draulic turbine. The…

A: Given: Diameter of the nozzle→d=10 Cm=0.10 m so the area of the nozzle→a=π4d2=π40.12=0.0078 m2…

Q: (1) Water Pump m L To double the outflow of a reservoir, a pump is added as shown in the Figure…

A:

Q: A petrol engine has mechanical efficiency 0.8 and lower calorific value of 44.2 MJ / kg. The engine…

A: Given Data: Mechanical Efficiency η=0.8 Calorific value C.V=44.2MJkg Bore D=0.06 m stroke L=0.08 m…

Q: Q.5 A pump circulates water through a closed pipe network connecting a water heater and a heating…

A:

Q: e power developed by the turbine.

A: To find Flow velocity Power developed

Q: Water (20°C, saturated) enters a 2 in. Sch. 40 pipe at a velocity of 1.0 m/s and a pressure of 1…

A:

Q: A pelton wheel is supplied with water under a head of 100 m at the rate 1000 litres/s. The bucket…

A:

Q: Water from a large reservoir drives a turbine, and exits as a free jet from a pipe of diameter D.…

A:

Q: A nozzle having a velocity coefficient of 0.98 discharges a jet 15 cm in diameter under a head of…

A:

Q: find  Step 1: Known, Unknown Step 2: Schematic Step 3: Formula Step 4: Calculations Step 5:…

A:

Q: Water is pumped into a fire hose through a 6 cm diameter pipe with speed 1m/s. The water in the fire…

A: Given, For 6 cm diameter hose, At the nozzle end, The density of the water,

Q: In the tank in water is under a layer of compressed air that is at 20 psig. The water is flowing out…

A: The gauge pressure of the air, The value of h is, Determine the exit velocity of the water.

Q: Q1/ Neglecting losses, determine the discharge in Fig. below Oil sp gr 0.75 3ft 4 in, diam Water

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.