Find the Total efongation of the bar below 12KN OKN 4KN 4KN+ 6KN LI 12 L3 L4

Q: For the section shown in Fig. P.4.1b, find the volumetric ratio of spiral which will make the…

A: Volumetric ratio = 0.45 (Ac/Ack-1) (fck/fy) Ac=196349.5 mm2 Ack=159043 mm2 VR =…

Q: The W350x90 section is used as a column as a column 10 m long. The column is fixed at one end and…

A:

Q: 2kN/m Find the deflection midway between the supports 4m 4m 4m

A:

Q: 3. Compute the reacting forces RA and Rg at the ends of the beam shown. These reacting forces are…

A: Given simply supported beam with inclined point load 130 N. It is asked to calculate support…

Q: 1. Problem Solving: Solve the following situations as completely as possible, use any method that…

A: P= 250 KN W= -7x+81 KN/m Note According to the company guidelines i am able to answer only first…

Q: Based on the the truss given, what is the value of force acting on member AD? * CO00 KN 24D KJ 0 Ham…

A:

Q: - In the cross section below, find:-

A:

Q: Question Bank - Friction Two concrete blocks weighing 1800N each form part of the retaining wall of…

A:

Q: 1.) Determine the resultant of the forces acting on the body. 450KN 600KN 2 1 4 200kN 15 12 2 250kN…

A:

Q: 8KN 2KN A Z 3M am 3m

A:

Q: Q2:- A rectangular gate AB in Fig is I m long and 1.Sm wide into the paper, hinged at 4, and resting…

A: formula to find force exerted on flat plates immersed in the water F=γAhγ= unit weight of liquidA=…

Q: 03 Figure 03 shows an overhead crane truss supported by pin and roller supports at point A and E.…

A:

Q: 07/16/2024 07:56 1. DETERMINE bi THE CENTROID & MOMENT tw IL ) h OF INERTIA h = 600 mm b₁ = 400 mm…

A: Step 1:Step 2:Step 3:Step 4:

Q: Determine the centroidal x-coordinate (in mm, round=off to 2 decimal places) of the wire figure…

A:

Q: 2) What is the deformation 8gc in mm?

A:

Q: Find By and Cy using compatibility equation E is 200 × 10 power 9m I is 2.6 × 10 power-10m…

A: Given EI is constant We are required to calculate By and Cy

Q: ● Analyze the simple truss shown.

A: Given:- To find:- Analysis of the truss

Q: 5 cm 12 cm 12 cm N1-2 0 = 30° N1-10 5 cm 15 cm

A: The problem involves determining the forces and moments acting on a mechanical system to ensure it…

Q: Dstermine the x, , and z-coordinates of the mass center of the body constructed of thres pisces of…

A: Determine the x-yandz-coordinates of the mass center of the body constructed of three places of…

Q: Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on the…

A:

Q: Deter mine the veta tron atpoint of the frame shown in figuve. Takke %3D E= 200x10 mpa / 1=3. x1o…

A:

Q: 5. 25 mm x- (horizontal) and y- (vertical) axis through the centroid of the two 250 x 25 mm steel…

A: Given Steel plate at top and bottom Channel section at right and left  Welded together to form cross…

Q: 3kN/m 25KN B A 2m 4m Зт

A:

Q: (A) mum mmmm (C) mm (D) mmm mim Which of the following most nearly the degree of static…

A:

Q: 5. Find the Total efongation of the bar below 12KN 6KN 4KN 4KN+ 6KN L1 12 L3 L4

A:

Q: (B) (C) mu (D) O Troge mm mm Which of the following most nearly the degree of static indeterminacy…

A:

Q: The University of Diyale College of Engineering Department of C Engreering Homework #4 Replace the…

A:

Q: Where must the force R be applied so that its external effect on the bar ABC will be the same as the…

A:

Q: Determine the force-couple system acting at point 0. 50 N 90 N 40° В 40 N m 400 mm 1300 mm A 4 800…

A:

Q: Find the moment of inertia with respect to X and Y axes Y 1cm 3cm Зст Зст 1cm 7cm

A: Schematic figure of the above problem:

Q: Ex's For the beam shown below, Find (Wii), use fo`=21/pa. EYE 400 Mpa.... Wu 5m. 100m 100m 100mm…

A: Given: b = 200 mm d = 350 mm span = 5 m fc = 21 MPa fy = 400 MPa

Q: need help.

A: A frame is there and all the information related to the frame are given in the question. we have to…

Q: find bar forces 6ft A Cskips sdra 9Tg 4 ft 4 ft 4 ft

A:

Q: 75% 130° F=10 N d= 5m

A: Given, Free body diagram of given figure:-

Q: SOLVE FOR THE SHEAR AND MOMENT DIAGRAM: USE ONLY AREA METHOD. SHOW COMPLETE SOLUTION FOR…

A: Given data: W1=77 KN/m W2=66 KN/m P1=21 KN P2=79 KN,   M1=127 KN.m

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?