Find the stresses which may induced in each rod if temperature increases by 70°C. Aluminum Bronze

Q: The beam is supported by two rods AB and CD that have cross- sectional areas of 13 mm² and 7.8 mm²,…

A:

Q: how did we go from 9.3kN to 7.5 kN for the load applied?

A:

Q: What will be the maximum diameter of a metal rod, which is used to raise a load of 1400N if the…

A:

Q: equation for tangential stress for thin walled cylinder

A: Given: Cylindrical vessels To define: Thick and thin walled pressure vessels To derive: Equation for…

Q: Calculate the largest weight W that can be supported by two wires. The stress in either wire is not…

A: Givenσ=7.6 MPaAAB=150 mm2AAC=250 mm2

Q: A titanium shaft has a starting diameter = 19.50 mm.  It is to be inserted into a hole in an…

A:

Q: Take o, = -400 kPa, Tzy = -330 kPa. (Figure 1) Part A Determine the equivalent normal-stress…

A:

Q: The two steel members are joined together using a 30° scarf weld. Forces of F = 13.5 kN are applied…

A: Given DataForce is : oLength is : Width is : Area on which force is acting

Q: A thin-walled cylinder is subjected to an internal pressure P. What is the ratio of the tangential…

A: Giventhin- walled cylinder internal pressure -P

Q: Question (5): (a) The device shown in Fig. (5-a) is designed to apply pressure when bonding laminate…

A: Given Data At the handle 120N force is applied  Let us draw the reaction at the roller supports

Q: A 5-mm thick hollow steel has an allowable stress limited to 200 MPa. Determine the inside and…

A: According to the question data F=100kN Do-Di =2t=10mm Do=Di+10 ----------(1) σallow=200MPa We need…

Q: Do larger members fail at comparatively lower stresses than smaller members?

A: When a moment or couple is acting over the member, then the size of the member is a matter of…

Q: A metallic rod of 500 mm length and 50 mm diameter, when subjected to a tensile force of 100 kN at…

A:

Q: The assembly is the same as in problem 2. It consists D of two rods AC and BD attached to the 100-lb…

A:

Q: The rigid, horizontal slab is attached to two identical copper rods. There is a 1. gap a = 0.18 mm…

A:

Q: Learning Goal: As shown, two composite columns of steel and concrete are used to support a rigid…

A:

Q: 8. 10 plate 8X10 - S00 pounds of loud material 6061 Aluminum - Determine what type of stress Is…

A: Hf

Q: Identify the indirect force in the following Select one: O Tensile O Both Tensile and Compressive O…

A: Solution:

Q: Please answer the attached question which includes all the necessary background information sourced…

A: The objective of the question is to find the value and location of the largest tensile and…

Q: The rigid bar AB as shown in Figure Q1(a) is supported by a steel road AC having a diameter of 22 mm…

A:

Q: A spherical vessel is to contain air at an average temperature of 25°C. The average mass is 250 kg.…

A:

Q: The rigid bar ABC is supported by a pin at B and two vertical steel rods. Initially the bar is…

A:

Q: The rigid bar of negligible weight is supported as shown. The assembly is initially stress- free.…

A: Answer: (a) The stress in the bronze bar is 50.78 MPa. (b) The stress in the steel bar is 52.11 MPa.…

Q: The compound bar, composed ot the three segments shown, is initially stress-free. Compute the stress…

A:

Q: What is the allowable contact stress number, sac, in MPa,  for ductile iron  ASTM A536,  60-40-18…

A: The maximum acceptable stress that material may withstand under contact or loading conditions is…

Q: The ultimate tensile stress of mild steel compared toultimate compressive stress is O more O less O…

A: Concept: 1)Mild steel is a ductile material.  2) For ductile materials, ultimate strength in tensile…

Q: Please answer both 1 and 2 as they relate to eachother. thank you in advance

A: Write the properties of 1040 steel.

Q: Part B - Clockwise Rotation of a Stress Element with Only One Normal Stress The state of stress at a…

A:

Q: CApans the temperature increase it would that number from the temperature er this contact and…

A:

Q: Question 4 4 of 10 The two aluminum rods support the vertical force of P = 16 kN (Figure 1)…

A: Given:- (A)

Q: le culate the values of prine

A: given:

Q: A 3D solid component is subject to external forces such that following three principal stresses are…

A:

Q: The diagram below shows a microscopic metal rod with a single crystal structure whose orientation is…

A:

Q: 1. Cast iron the refined form of ? a- Pig iron b- carbon C- molybdenum

A: (1) When the pig iron is remelted in the small furnaces(cupola) and after that poured into the molds…

Q: 1) How much stress will be generated in the 13mm diameter aluminum rod below with an increase in…

A:

Q: 0 kN. Determine the required cross-sectional area of the wable stresses are 6 MPa for concrete and…

A: Need to determine the cross-Sectional area of reinforcing steel

Q: Compound axial member ABC has a uniform diameter of d-2.4 in. Segment (1) is an aluminum [E₁ -…

A:

Q: How can the normal stress distribution be determined?

A: When a body undergoes deformation under normal or shear forces/loads, then it undergoes…

Q: 1) How much stress will be generated in the 13mm diameter aluminum rod below with an increase in…

A: Answer: The stress generated in the aluminum rod is 13.89 MPa.

Q: When a statically determinate structure is heated or cooled, its members do not experience…

A: When a statically determinate structure is heated or cooled, its members do not experience…

Q: Statement: At any point in a body subjected to load, therer are different stresses or cominations of…

A: the above statement is abosuloutely correct    when a body is subjected to load different stress…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.