Find the Reduced Level (R.L.) of each station? (Use Rise and Fall Method only) Stations Readings R.L. (ft.) Remarks B.S. (ft.) I.S. (ft.) F.S. (ft.) A 4.320 007 B.M. B 3.352 C 3.000 D 1.586 2.367 C.P. E 2.490 F 3.612 G 4.012

Find the Reduced Level (R.L.) of each station? (Use Rise and Fall Method only) Stations Readings R.L. (ft.) Remarks B.S. (ft.) I.S. (ft.) F.S. (ft.) A 4.320 007 B.M. B 3.352 C 3.000 D 1.586 2.367 C.P. E 2.490 F 3.612 G 4.012

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q.1 A line of level is run from B.M.1 (elevation=106.40m) to B.M. 2(elevation=110.50m). The field…

A: Given Elevation of bm1=106.40m Elevation of bm2=110.50m To find Reduce the level of point 2, 3, 4…

Q: Find distance db

A: To find distance db

Q: Q.1 A line of level is run from B.M.1 (elevation=106.40m) to B.M. 2(elevation=110.50m). The field…

Q: Line Distance AB BC CD DE EF FG 62.56 29.49 65.07 41.14 43.70 26.74 Forward Bearing N 81-02-05 W N…

A: Given: LINE FB BB AB N 81-02-05 W S 79-26-30 E BC N 08-16-07 W S 13-18-15 E CD S 87-34-45 E…

Q: A panel of 30 rooms in a room-and-pillar coal mine is to be driven from a set of three room entries…

A: Generally, a pillar refers to any isolated vertical structural part, such as a post, column, or…

Q: If you know the distance between the road centerline (source of traffic noise) and receiver was 10m…

Q: 2000 KN 400 kN/m 200 kN/m mm sn -10 -10 m For the beam loaded as shown, what is the location where…

A: It is asked to determine For the given beam and loading, the location of zero slope from the right…

Q: Problem #4 Compute for the resultant of the given Parallel system and its relative position from…

A: Determine the resultant of the load and it's relative position from point A.

Q: Compute the DPD of each lines (AB, BC, CD, DE, EF, FA)

Q: COURSE DISTANCE (m) BEARING AB 105.67 N 30.15° E BC 126.15 N 74.18° E CD S 40.31° E --- DE 127.77 S…

A: A closed traverse ABCDEFA is given in which length of CD and bearing of FA is missing and it has…

Q: 4. Convert 150 o to radians 5. Convert 5. 64 rad to degrees G. Convert 2 2. 6 78 ° TO degrees,…

Q: A panel of 30 rooms in a room-and-pillar coal mine is to be driven from a set of three room entries…

A: Generally, a pillar refers to any isolated vertical structural part, such as a post, column, or…

Q: 20KN 60KN 10KN/m 2mA 5m 6m 2m 4m A B) D E 2. 51 21

Q: 3.44 Solve for CD, HD, and HG. A 60° B 10⁰ I C 10¹ 41. H 2K 10' 6 E 4K ANERKENA 10¹ F

A: Given Data Find the forces in member CD, HD and HG.

Q: Find the shaded area for the following figure y 0.5- -0.5 0.5 -0.5

Q: Three stations P, R and Q are along the same plane. Angle of elevation of the top of signal of…

Q: Find moment at D and C. Please answer fast and don't copy from anywhere. Use any method

A: Given:- To find:- Moment at D Moment at C Concept:- Moment distribution method:- Moment…

Q: STA BS HI FS IFS ELEV BMa 0.95 125.50m 0+ 00 3.0 + 10 2.3 TP1 3.13 0.64 0 + 22 + 30.5 + 34. 2 + 39.3…

Q: Н.W. Stations B.S (m) I.S (m) F.S (m) Elevation (m) Remarks A 0.400 100 BM 0.765 C 1.270 2.560 3.220…

A: Calculating reduced level of all the point , which satisfy following relation-∑Back sight-∑Front…

Q: STA BS HI FS IFS ELEV BMa 0.95 125.50m 0 + 00 + 10 3.0 2.3 TP1 3.13 0.64 0 + 22 2.7

A: The elevation is generally the vertical distance from a datum that is the sea level, to a point on…

Q: A (150,100) 442) H O B (190, 210) A2.330° T 25th TG M (2305100) ↑ ( (280) 100) Compute the area of…

A: Given:

Q: 40 Nim 20N/m

Q: Continuation from Question no. 3: Determine the horizontal reaction at C. B 76.33 KN 75.33 KN 74.33…

Q: 610 A 25 B 53.18° k 151 GR MAG 80 k 201 MBA+MAB (25) (12) for b 16.6671 न 20 Мос How did this value…

A: The below structure is shown;

Q: - A 500 mm x 500 mm square tied column shown is reinforced with 10- 26 mm diameter bars with a steel…

A: Given:- The dimension of the column = 500 mm × 500 mm The steel reinforcement provided = 10-26 mm…

Q: Two stations “A” and “B” are 65 km apart and having elevation of 210 m and 300 m above mean sea…

A: This problem is related to Surveying Engineering. In this problem given elevation of station A and B…

Q: The DMD of the line 2-3 was found to be 512.13. If the departure and latitude of the preceding line…

A: Given DMD of line 2-3 = 512.13 Departure of preceding line 1-2 = 213.82 Latitude of preceding line…

Q: ree of static indeterminac

A: Given:- Beam To find:- degree of static indeterminacy

Q: THE MAGNITUDE OF THE RESULTANT O TOTAL MOMENT ACTING ON POINT "A" TOTAL MOMENT ACTING ON POINT "B“ ο…

Q: 2000-8", C = 100 El. 300.0 4000-16 C-100 EL 280.0 S000–10" E C-130 El. 230.0 20,000-12 C- 90 El.…

A: Estimate of pressure head at E = 250' ( other values can also be assumed, based on the assumed…

Q: The R.L, of the point A which is on the floor is 100 m and backsight reading on A is 2.455 m. If the…

Q: 12.find interval normal moment

A: in above structure there are two hinge joint at S1 and S2 location. as we know, hinge releases all…

Q: Q.1 A line of level is run from B.M.1 (elevation=106.40m) to B.M. 2(elevation=110.50m). The field…

A: Given B.M.1 (elevation=106.40m) B.M. 2(elevation=110.50m). To find elevation of points 2,3,4 and 5

Q: The following consecutive readings were taken with auto level and a staff of length 4 m along the…

A: Given, RL of the last station= 200.200m And consecutive readings, 3.105, 2.120, 1.115, 0.410, 3.655,…

Q: Q1). The following consecutive readings were taken along a straight line from station (11+090) to…

A: Solution: Station B.S I.S F.S 1 0.680 2 1.455 3 1.855 4 2.330 5…

Q: y -8.71- R7.81 10.44- 13.10- -.9.17---

Q: Q1: for carrying out contour survey in a hilly area and why? (CLO1, C1, PLO1)(10) b) What are the…

A: Method of contouring:

Q: A total station with a 20"/div. level bubble is one division out of level on a point with an…

A: Given: s = 20" No. of division out of the level bubble, n = 1 Altitude angle, θ = 36o36'36" To find:…

Q: Find the courdinates of the centroid of the shaded areas shown below. 3- 12" m.com MATHalino.com 6+

Q: What is TP 3 elevation shown in the picture below: H.I. H.I. 11.68 .92 1.22 7.84 H.I, 2.05 3.10 TP 3…

Concept explainers

State Plane Coordinate Systems

The state plane coordinate system (SPCS or SPS) is a collection of 124 coordinate systems or geographic zones prepared for particular regions of the U.S. Every state consists of one or more than one state plane zone, the boundaries of which generally follow the county lines. Inside the U.S., there are 110 zones in total, 10 more zones in Alaska, 5 in Hawaii, and 1 for Puerto Rico and US Virgin islands. The system is extensively used for geospatial and geographic data assembling by the state and local governments.

Question

Find the Reduced Level (R.L.) of each station? (Use Rise and Fall Method only)

Stations	Readings	R.L. (ft.)	Remarks
B.S. (ft.)	I.S. (ft.)	F.S. (ft.)
A	4.320			007	B.M.
B		3.352
C		3.000
D	1.586		2.367		C.P.
E		2.490
F		3.612
G			4.012

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

العنوان не ➤ The following observations were recorded when carrying stadia level between two temporary bench marks. ➤ If the elevation of TBM1 is 750.0 m, compute the elevation of TBM2. Back sight Fore sight Stat. interval Rod read. v.angle interval Rod v.angle read TMB1 3.14 8.6 -0° 25' TP1 5.02 4.5 -3 15 5.02 6.3 +1 52 TP2 4.88 10.0 -1 02 2.74 2.2 +6 20 TP3 6.08 8.0 +0 36 8.06 5.0 +6 13 TP4 1.96 5.5 -5 52 4.81 8.5 -4.00 5.92 12.2 -1 13 TBM2 ۱/۱ S で T =T [く] M
Solve for this prob. Formula: H.I. = Elevation of given B.M. + B.S. Elevation of T.P. = H.I. – F.S. Ground Elevation at Centerline Station = H.I. – I.F.S. Error of Closure (e) = SB.S - SF.S. Error of Closure = Elev B.M. – Elev. of the last point
The DMD of the line 2-3 was found to be 512.13. If the departure and latitude of the preceding line 1-2 is 213.82 and 215.16, respectively. Determine the departure of line 2-3.Note: Round off your answer to the nearest tenth
Q.1 A line of level is run from B.M .1 (elevation=102.00m) to B.M. 2(elevation=106.00m). The field observations were recorded as given below: Station В. S I.S F. S Remarks 1 1.95 В.М. 1 2 0.65 2.60 1.45 4 -1.90 -1.60 5 0.55 6 0.50 В.М. 2 Reduce the level of point 2, 3, 4 and 5, determine the total error of closure, and adjust the values.
What is the back azimuth of a line has an azimuth 267°?
A level instrument at a height of 1.320 m has been placed at a station having a Reduced Level (RL) of 112.565 m. The instrument reads -2.835 m on a levelling staff held at the bottom of a bridge deck. The RL (in m) of the bottom of the bridge deck is A. 116.720 B. 116.080 C. 114.080 D. 111.050
A В 196 N P 294 N
pls help me solve this. 1) a transit with stadia interval factor of 100.8 was set up at point C on the line bet. A and B. The ff. readings were observed: (*see from attached photo) If the distance from the focus is 0.38m. determine the ff.: a) horizontal distance bet. A and B b) Diff. in elevation bet. A and B of the value of HI are 300m and 315m respectively.
Draw/ Illustrate the profile leveling The second photo is an example of profile leveling Thank you!
Q3: Find the elevation of all point if the elevation of Last point is 30 m and check the results. (25 %) Station B.S F.S elevation В.М 1.245 T.P, 3.254 2.523 T.P2 2.522 1.421 T.P3 1.242 0.263 3.486 30
A-15 m- 33 m Q2) The figure to the right shows a rectangle ABCD, in which A, B, and C are the stations where staff readings were obtained with a level set up at E and D. The observed readings are given in Table. 20 m Staff reading at level location A B C 1.85 0.803 D 2.42 1.361 1.659 48 m If A is a benchmark having elevation of 70 m. Note: the deflection angle in Line of sight (5) is + 0.1146 degree. Level 1. calculate the correct elevations B and C 2. if the height of instrument at E = 1m, and at D= 1m, what is the height difference between D and E
plete the following levelling booking and late the reduced levels of all stations by body the rise and fall and height of collimation methods. Apply all arithmetic checks possible. (Engineering Council) BS 1.76 1.05 1:53 0.94 0.51 -0.61 0.32 1.01 FS 1:34 1.09 0.33 d pue # RL 100.00 Station ABCDEFUI G Jaur and se