Find the mass of coarse and fine aggregate required for the mix design using the following parameters i. ii. ii. w/c ratio = 0.4 water content = 150 kg/m3 fine to total aggregate ratio = 0.4 Density of fresh concrete = 2400 kg/m3. iv. For example, the following selected values of mix parameters may be used to calculate the mass of water, cement, fine aggregate and coarse aggregate for producing 1 m' of concrete:

Find the mass of coarse and fine aggregate required for the mix design using the following parameters i. ii. ii. w/c ratio = 0.4 water content = 150 kg/m3 fine to total aggregate ratio = 0.4 Density of fresh concrete = 2400 kg/m3. iv. For example, the following selected values of mix parameters may be used to calculate the mass of water, cement, fine aggregate and coarse aggregate for producing 1 m' of concrete:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the given concrete mix design below, calculate the field weight of the ingredients in kg's if the absorption capacities of both aggregates are 1%, total moisture content of coarse aggregate is 2% and the total moisture content of fine aggregate is 4%? Ingredient Weight in kg per m³ Cement 300 Water 150 1000 800 SSD Coarse aggregate SSD Fine aggregate Fine aggregate: Seç... ÷ Coarse aggregate: Seç... Seç Water: + ÷
What is the weight of fine aggregates in kilograms needed for the design mix? Use three decimal places in the computation of volumes Use two decimal places for the computed weight of fine aggregates
A civil engineer wants to design a concrete mix design with the following criteria: Design a concrete strength: 25 MPa with a slump of 90 mm. Ignore the need for exposure Select a non-air entrained concrete Fine aggregates properties: Fineness modulus 2.67; Bulk specific gravity 2.66 Coarse aggregates properties: Maximum size aggregate of 25 mm with the bulk specific gravity 2.55 and dry-rodded mass 2000 kg/m3. Based on the criteria above 2.1. Calculate the required strength. 2.2. Calculate the water cement ratio. 2.3. Calculate the mix proportions of all materials including cement, water, fine aggregates, coarse aggregates, and air content for 1 m3.
SECTION A Answer ALL Questions Physical and mechanical properties of civil engineering materials, their behaviour and characteristics in design and construction works. Answer below questions using your own words and understanding. (a) (i) Design a concrete mix for the following given data: A mean 28-day compressive strength (measured on standard cubes) of 45 MPa Slump = 40 mm, Uncrushed aggregate with maximum size of 20 mm Specific gravity of aggregate = 2.64 Fine aggregate passes through the 600 µm sieve = 48% No air entrainment required, ordinary Portland cement to be used. [Use supplied charts and table to get required values]
A concrete mix consists of 5 gallons of water for each bag of cement. What is the expected compressive strength of this mix based on the compressive strength curve shown here? Given information: Weight of US standard cement bag = 94 lbs Water weight = 8.34 pounds per gallon COMPRESSIVE STRENGTH psi 6000 5000 4000 3000 2000 0.3 0.4 6000 psi 5000 psi 4000 psi 3000 psi NORMAL CONCRETE 0.5 0.6 W/C RATIO 0.7 MPa 42 35 28 21 14 0.8
26 - please show complete solution, thanks!
Design a concrete mix which is already solved by using Eprical Formulas according to TS-EN and compate the results.
The following mix design information is provided to you for 1 m³ concrete. • Air content = 5% • w/cm = 0.7 • cement Gsb = 3.000 • water = 158 kg, density = 1000 kg/m³ • Coarse aggregate (CA) with Gsb = 2.695 and fine aggregate (FA) with Gsb = 2.690 What is the total volume of aggregates (CA + FA) in the mix (in m³)?
Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to be blended. The results are as follows:Aggregate A: Bulk specific gravity = 2.491; absorption = 0.8,Aggregate B: Bulk specific gravity = 2.773; absorption = 4.6,a. What is the specific gravity of a mixture of 60% aggregate A and 40% aggregate B by weight?b. What is the absorption of the mixture?
Based from the proportion that you have designed, say that the concrete is mixed to fill 20 cubes (100 x 100 x 100mm) and 10 prisms (500 x 100 x 100mm), find the mass of each material based on the aggregate conditions in Table 2.
Q2. The data of material for making a cement concrete mix may be assumed as follows: (i) Water-Cement ratio by mass = 0.46 (ii) Entrained air = 2% S.No. Material Specific Bulk gravity density 1. 2. 3. Cement Fine aggregate 20 mm nominal size crushed coarse aggregate 3.15 2.61 2.7 (Kg/m³) dry 1500 1620 Proportion in mix by 1530 volume 1 part 1.359 part 2.79 part Determine the following for cement concrete: (1) Absolute volume of fully compacted fresh concrete (ignoring air content) produced by one bag of cement of 50kg. (2) Cement content per cubic metre of concrete. (3) Quantity of material to make one cubic metre of concrete.
I need answer within 20 minutes please please with my best wishes