Answered: Find the largest allowable time… | bartleby

Related questions

Question

2- Find the largest allowable time constant for this sensor.
A 10-in-stroke wirewound translational potentiometer is excited with 100 V.
The output is read on an oscilloscope with a "sensitivity" of 0.5 m V /cm. It
would appear that measurements to the nearest 0.0001 in are easily possible.
Explain why this is not so.

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Oxygenated hemoglobin absorbs weakly in the red (hence its red color) and strongly in the near infrared, whereas deoxygenated hemoglobin has the opposite absorption. This fact is used in a "pulse oximeter" to measure oxygen saturation in arterial blood. The device clips onto the end of a person's finger and has two light-emitting diodes-a red (635 nm) and an infrared (935 nm) -and a photocell that detects the amount of light transmitted through the finger at each wavelength. (a) Determine the frequency of each of these light sources. red Hz infrared Hz (b) If 63% of the energy of the red source is absorbed in the blood, by what factor does the amplitude of the electromagnetic wave change? Hint: The intensity of the wave is equal to the average power per unit area as given by 2 E max I = -B, 2H0 2. max
Needs Complete solution with 100 % accuracy don't use chat gpt or ai plz plz plz.
Oxygenated hemoglobin absorbs weakly in the red (hence its red color) and strongly in the near infrared, whereas deoxygenated hemoglobin has the opposite absorption. This fact is used in a "pulse oximeter" to measure oxygen saturation in arterial blood. The device clips onto the end of a person's finger and has two light-emitting diodes-a red (636 nm) and an infrared (922 nm)-and a photocell that detects the amount of light transmitted through the finger at each wavelength. (a) Determine the frequency of each of these light sources. 4.72 red Your response differs significantly from the correct answer. Rework your solution from the beginning and check each step carefully. Hz 3.25 infrared Your response differs significantly from the correct answer. Rework your solution from the beginning and check each step carefully. Hz
Needs Complete typed solution with 100% accuracy.
+ 10 Page view A Read aloud V Draw Highlig! Question 1 (a).i. An electric heating element to dissipate 580W on 240V is to be made from nichrome ribbon 1mm wide and thickness of 0.005mm. Calculate the length of the ribbon required if the resistivity of nichrome is 1. 1x 100m. (6marks) 1. The resistance of a coil aluminum wire at 21°C is 2100. The temperature of the wire is increased and the resistance rises to 2400. If the coefficient of resistance of aluminum is 0.0039/c at 21°C, determine the temperature to which the coil has risen. (7marks) b) A capacitor is constructed with parallel plates and has a value of 50pF. What would be the capacitance of the capacitor if the plate area is doubled and the plate spacing is halved? (7marks) c) Calculate the current / that will flow through the circuit shown below: 16Ω 1.50 20 24 V 60 502 30 (5marks
Q2a Assume the following values for the Staircase ADC shown below: clock frequency = 100 kHz; VT (Threshold voltage) = 0.1mV; DAC has a full scale output: 10.23V and a 10-bit input. = Op amp Comparator D/A converter Digital resull EOC (a) RESET Counter CLOCK Start r Clock START VAX EOC (b) Conversion complete. counter stops counting Time Determine the following values. (a) The digital equivalent obtained for VA = 3.580V. (b) The total conversion time for (a)
The capacitor in the circuit shown is fully charged by a 24 V battery. The switch is closed at t = 0. At sometime after the switch is closed, the voltage across the capacitor is measured to be 10 V. What is the current in the circuit at this time, in Ampere? C = 3.0 µF, and R = 2.0 02. Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. Cil
Page No : Date: a currentof current be the Tnductor? A 18 H Tn ductor carv Pes QA. At what rate mast the changed to produce a GoV emf Pn
Q4
In some systems a negative convention is being applied: the LOW signals are representing logical 1 and HIGH signals are representing logical 0. How does a negative convention affect the basic logic gates OR, AND, XOR and NOT? (I.e. what are the truth tables and the name/function of the logic gates in the negative convention?).