FIND THE INVERSE 257 A=

Q: A stone is dropped down a well and 5 sec later, the sounds of the splash is heard. If the velocity…

A:

Q: Volume ama the itCTIlal CHcrgy. 4. A vessel of a volume 0.03m3 contains dry saturated steam at 20…

A:

Q: The cylinder of an Ideal Dual Combustion has a bore of 7 inches and a stroke of 7.5 inches. The…

A: Stroke length, L=7inches=177.8mm=0.1778mDiameter of cylinder, D=7.5inches=190.5mm=0.1905mSpeed of…

Q: Find the value of a. TO a. Vs +3

A:

Q: ply Jackson and Morela in the Figure Problem 8 ermitted

A: Given:

Q: Question No.3 dM The bending moment M of the beam is given by dx -w(l – x) where w is a constant %3D…

A:

Q: 4. In raising the pole from the position shown, the tension T in the cable must supply a…

A:

Q: 2. If force F is to have a component along the u axis of Fu = 6kN, determine the magnitude of F and…

A:

Q: 150 200 mm D mm 150 150 v2 mm mm 0 = 45° E 12.5 rad/s

A: Given data,θ=45°ω=10 rad/sOB=1502mm=0.2155mAB=350mm=0.3556mO'A=150=0.1524m

Q: Backgrour grid Exit jet

A:

Q: A section of double-extra-strong pipe made of steel with yield strength Oy = 50ksi is subjected to a…

A: Write the given data with suitable variables. σY=50 ksiM=114.2 kip-inT=254.2 kip-indi=2.3 indo=3.5…

Q: L 32 mm L Cross-section K, aran : 17 nam + 6 E= 200 kN/mm m = 15 kg KI= lo kN/m Find f

A:

Q: A particle of mass m and kinetic energy E > 0 approaches a delta-function barrier located at x = 0:…

A:

Q: instantaneous discharge velocity

A: Given; Large tank with a nozzle attached contains three immiscible,   inviscid fluids as…

Q: slope and deflection at end A.

A: for solution refer below images.

Q: The three flat blocks are positioned on the 30° incline as shown, and a force P parallel to the…

A: Given:-Block 1=30 kgBlock 2=50 kgBlock 3=40 kgθ=30°For 1 and 2, μs=0.30For 2 and 3, μs=0.40For 4 and…

Q: Determire the internal shear force at section 0.5 m from point B to the right in the rigid body…

A:

Q: 4-The fluctuation in pitot tube reading during velocity distribution experiment is due to

A: As per the answer asked only for the question No 4. So here is the answer for Q.4. Pitot Tube: In…

Q: determine the tension in cable AC and in cable BC.

A:

Q: PROBLEM # 3 1. A solid block is 70 cm wide, 80 cm long and 20 cm tall, and Estimate the solid block…

A: Solid Block

Q: A 1200 Ibs force acts as shown on a 500 Ibs block placed on a horizontal plane surface. Determine…

A: .

Q: 1. Determine the component of each force along the specified x - y axes. Refer figu 1. the exclusive…

A:

Q: A section of double-extra-strong pipe made of steel with yield strength Oy = 50ksi is subjected to a…

A: Given data R=78 Ksi= Kilo pound per square inch and kip=1000 pound force  σy=50Ksi=50×103…

Q: A 60° strain rosette is glued to a girder. Under certain loading conditions at an instant, the…

A: Given data, εa = Strain at strain rosette a = 4.4x78 μ = 343.2μ εb = Strain at strain rosette b =…

Q: PROVE THAT THE ANGLE IS 30° BY LAWS OF CONGRUENCY

A:

Q: Finding the third projection

A:

Q: Given, HRB = 4X Find BHN. Given, HRC = 3X %3D Find BHN.

A: Hardness : it is the property of the any material that tell the resistance ability to abrasion or…

Q: 3 2 ll M2 HE Mi skga bF friction less surfau

A:

Q: 5. Determine the moment of the 360N about a) point A, and b) point B 360 N 40° 100 mm 225 mm A 25•…

A: Given data: F=360 N Need to determine the moment about the point A and B.

Q: 3. Determine the components of force F along the x - y axes which are parallel and perpendicular to…

A:

Q: QUESTION 4 spring-1 Unknown mass, wwwmf attached to the free end of a spring (the other end of the…

A: Given data  f1= 5.883Hz f2= 4.222Hz Find the value of frequency (f).

Q: Question 3a) 3 decimal points in inches * Locate the centroid of the shaded area а) х-ахis b)y-аxis…

A:

Q: Question 7a) 3 decimal points in meters * A bullet is fired at an initial velocity of 150 m/s and an…

A:

Atomic diffusion in solids

In material science, diffusion can take place in solid, liquid, and gases. In solids, atomic diffusion can take place with the help of thermally activated and randomly vibrating atoms. The atomic diffusion in solids is complex and very slow in comparison to atomic diffusion in liquids and gases because the interatomic distance between the atoms is smaller in solids as compared to liquids and gases.