Find the centre of mass of the uniform lamina ABCDE shown below. E бст 30 A 10cm B The shape is symmetrical about the line through C.

Q: .4 || (cos²e + sin?e) dp dz de 8 2(0*cos?8 + p*sin?e) p dp dz de

A:

Q: H. 50 MLLKI = %3D 188 mīJ = 46

A: The measure of arc KH⏜=188° The measure of arc HI⏜=50° The measure of ∠HJM=46°

Q: b. The drawing shows a sulfur dioxide molecule, S02. It consists of two oxygen atoms and a sulfur…

A: Given:

Q: P. Manufacturing A conveyor belt 12 in. wide is moving at a linear speed of 120 ft/min. The belt is…

A:

Q: B. (xp, Yp, Zg) ft * (xa, Ya» Za) ft Consider the given values for the force system shown above: XA…

A: Given the vector point of A=5+C,2+D,1+E, B=-15+B,3+A,13-C and C=3+C,5-B,4+A. From the given values:…

Q: Find the displacement and distance traveled of ritt:(1-3siatis costj osts

A: Givenr(t) = (1-3sint) i + 3cost j ;  0≤t≤3π2

Q: B E F H Given the diagram below, if H is the centroid of ABCD, BG=57, CD= 34, EH = 15, and CF = 39,…

A: Given the diagram below. if H is the centroid of ∆BCD,  BG=57, CD=34, EH=15, and CF=39, to find…

Q: 1. y MAIN is a rectangle 2. BEAM is a parallelogram M(c,b) B M(0,b) A A(0,0) E(a,0) VN(0,0) Ца, 0)…

A:

Q: Given a right ALHT with right angle at H, then mLT 30° and LT 18cm, 8. Find LH. %3D а. 9 ст b. 9/3…

A:

Q: 1. Let u = PQ and v = PR, where P = (2, –1,3), Q = (0,5, 1), and R = (5,5, %3D (a) u v (b) The angle…

A:

Q: Find the dot product v•w and the angle between v and w.   v=i−2j+4k​, w=3i+j+3k   v . w =?

A:

Q: Consider the parullelepiped with Sider. t-Findthe Volume of the Paralletefiped 2 Findthe…

A:

Q: E G PF 256° 14 сm 2) What is the Area of the Sector above?

A:

Q: Express the force as a Cartesian vector Z. 45° F = 500 N 60°

A: Given that                     angle made with x -axis be  α=θ. angle made with y-axis is    β=135°…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: A commuter airplane starts from an airport and it first flies to a city A located at 200 km on a…

A:

Q: Order the following statements and reasons to prove ABDE ACDE. Start with the given statement. #…

A: We have to show congruence of triangle

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Given  Positive force are tensile and negative force are compression.we need to determine force at…

Q: Determine the moment of Inertia about the Y axis for the sections shown below. 20cm 5cm 15cm 5cm Scm…

A:

Q: u = (2 + i, 0, 4- 5i) and v = (1 + i, 2 + i, 0).

A: Two points in complex plane is given.

Q: The point (-12, 15) is dilated by a scale factor of with the origin as the center of dilation. What…

A:

Q: Using the methods of this article, determine the surface area A and volume V of the body formed by…

A: Solution :-

Q: There is a partial insurance policy that pays $80,000 upon the bad drought state (and $0 in the…

A:

Q: (2) The three forces acting on the rectangular plate can be reduced to one single resultant force.…

A:

Q: E is the midpoint of CF and H is the midpoint of GI. What is the value of b? I 4b D G ww LL

A:

Q: Consider a parallelogram with diagonals of length of 25.8 and 30.8 respectively. These two diagonals…

A: Given: Lengths - 25.8 and 30.8    Angle = 42.4°

Q: Use the picture below and give the requested measure. (AB | GC, AĞ | BË and AF | D ) 48 60 36 E D…

A: Area of parallelogram is given by- A1=base×height Height of parallelogram= 48, Base of…

Q: 12 Fill in the 0/1 Blank Text If PQRS is a rectangle, fine the measure of ZQPT (10x + 1)° R T S (16х…

A: Topic:- parallel lines and alternative angle

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Given the figure is

Cylinders

A cylinder is a three-dimensional solid shape with two parallel and congruent circular bases, joined by a curved surface at a fixed distance. A cylinder has an infinite curvilinear surface.

Cones

A cone is a three-dimensional solid shape having a flat base and a pointed edge at the top. The flat base of the cone tapers smoothly to form the pointed edge known as the apex. The flat base of the cone can either be circular or elliptical. A cone is drawn by joining the apex to all points on the base, using segments, lines, or half-lines, provided that the apex and the base both are in different planes.