Find the cam diameter and actual volume displaced? Volumetric efficiency 1420 rpm, e = 14.67 mm, L = 53.12 mm, Rotor diameter = 77.56 mm, Volume Vane pump, = 91.87%, N = %3D displaced = 288.43 cm³-rev1. %3D

Q: What are Landfills ?

A: Landfills are deliberately constructed structure that are built into or on top of the earth,…

Q: What is the purpose of Home Maintenance/Construction

A: Basic purpose related to home construction/maintenance are as follows:  All human beings require…

Q: What are some of the construction problems?

A: Construction sites are prone to many mishappenings. One cannot predict the  risk involved in an…

Q: AGREEN BUILDING DESIGN FOR A GOVERNMENT CENTER, AND BIBAK DORM" STRENGTH WEAKNESS OPPORTUNITY THREAT…

A:

Q: Is a wastewater treatment facility a better option?

A: Yes, a wastewater treatment facility is a better option. The main motive of wastewater treatment is…

Q: Explain

A: The signature and seal of an expired licensed civil engineer is not valid and acceptable. As per…

Q: 1.3 Plumbing materials, system design, and installation procedures are regulated by various…

A: There are several national and international standards and accreditation authorities, thus this…

Q: how poor drainage system cause water logging and soil salinity ?

A: Brief concept- Drainage system- Drainage system is necessary for the smooth removal of the waste…

Q: How are the Specifications important to the Inspectors?

A: - Inspection is an important and necessary step to ensure the safety and good working and…

Q: What is Design-Build Risk?

A: - Design build is a modern technique in construction in which owner provides the complete…

Q: Give a few suggestions that might be used to ensure adequate change control on projects using…

A: Change control is a way to take all the various variable things that can happen in the respective…

Q: Enlist at least five engineering design failures and give your opinion on each proje

A: Solution: 1. Failure in understand the specifications: Engineer always remind themselves that they…

Q: What is Total Installed Cost?

A: total project cost is the sum of the direct and indirect cost. the direct cost is for accomplishing…

Q: Define the Ultimate limit state categories and verifications ?

A: Limit State Method :  1. Limit state design (LSD), also known as Load And Resistance Factor Design…

Q: List three violations of construction standards and suggest two ways of prevention.

A: To determine: three violations of construction standards and suggest two ways of prevention.

Q: what are the pipes that can handle contaminated water

A:

Q: Define the term building regulations, ordinances, and permits?

A: Building Regulations are defined as how to construct a new building or modification.

Q: How should they be resolved? a. Improper Electrical Wiring b. Plumbing Problems c. Minor Structural…

A: To fix the problem, turn off the power to the device, then disconnect the wires and either clip off…

Q: elp me write a planning report for below topic: estimating stockpile volume when designing a road

A: From the given question it is required to mention the planning report for estimating stockpile…

Q: Where is the solution of item C

A:

Q: What are the requirements of the specifications that call for certificates of compliance?

A: The  certificate which gives the information that the company or organization has met certain sets…

Q: ist 10 facts about residential housing. List 10 facts about multiunit housing List and define 10…

A: Multifamily housing and residential housing are integral parts of our built environment. Residential…

Q: What cost savings does a centrally controlled IP-based building security system provide?

A: Centrally controlled IP-based building security uses a single set of software which can be…

Q: What are the ancillary permits to supplement the Building Permits?

A: The goal of ancillary permits would be to ensure that the appropriate expert is held responsible in…

Q: What types of equipment are used for building maintenance?

A: There different equipment's used for the building maintenance  like free standing and the build in…

Q: meant by the term triage?

A: It is a general term it means when doctor receive two or more patients with different degree of…

Q: Why are still cameras are used in the construction project?

A:

Q: Define the term quality control in construction?

A: Quality control is a set of procedures or methods meant to guarantee that a performed service or a…

Q: What are agency permits?

A: Agency Permit : Agency permit is an official approval or permission for the work from the concerned…

Q: What is an RFI and how is it used?

A: The RFI is an abbreviation of Request for Information, it is a standard process whose purpose is for…

Q: Describe the Sources of Groundwater Contamination.

A: Groundwater is defined as the water below the surface of water which is stored in the spaces . It is…

Q: Is the approval of shop drawings risky?

A: Shop drawings are the set of drawings produced by the contractor, supplier, manufacturer,…

Q: What is aerator? Explain different type of aerators with sketches

A: It is asked in the question to determine what is aerator and explain different types of aerators

Q: Demonstrate how safety and health management system will be able to reduce the construction cost.

A: OSHA represents Occupational Safety and Health Administrative. OSHA is a government managed agency…

Q: What is NPSH ? What is the difference NPSH available and NPSH required

A: This question is from Fluid Mechanics and Hydraulic Machines.

Q: What is structural database testing, and how is it distinguished from other types of testing?

A: The 3 types of Database Testing are Structural Testing Functional Testing Non-functional Testing…

Q: Who is responsible for developing an inspection plan?

A: Inspection of any sort of work is an important parameter for ensuring its safety, performance and…

Q: Define the term vadose zone.

A: Vadose zone is defined as the zone which lies between the water table and top of the ground surface.

Q: What are the various levels of LEED certification and how many points are required to achieve each…

A: The Leadership in Energy and Environment Design (LEED) is a commercial building certification…

Q: Although the LEED system is the most widely used with many users, several other rating systems have…

A: Building environment assessment (BEA), is defined as a term that is used to evaluate environment…

Q: What are the provisions for temporary facilities?

A: - Temporary facilities are generally provided during the commencement of project for staff and…

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.