Answered: Find the BER of a 64-QAM system with…

Engineering

Electrical Engineering

Find the BER of a 64-QAM system with SNR=10 dB. NOTE: Use Q-function table as needed.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Related questions

Q: dentify the addressing mode for each of the following 8085 instructions:

A: 1. MOV M,C : Register Indirect addressing mode It moves the content register into the memory…

Q: 2. This problem addresses the digitization of a television signal using pulse-code modulation. The…

A: 2. Signal bandwidth, B = 4.5MHz Sampling frequency, fs = 15% excess of NyQuil rate Number of…

Q: 8. Which characteristic of IC in Digital Circuits represents a function of the switching time of a…

A: The solution is provided in the following section.

Q: 4. This problem addresses the digitization of a television signal using pulse-code modulation. The…

Q: 8. Which characteristic of IC in Digital Circuits represents a function of the switching time of a…

A: The solution is provided in the following section.

Q: are specifications of Digital modulation techniques?

A: Digital Modulation Techniques. It is the kind of process in which encode a digital information…

Q: Q3) Twenty voice signals are sampled uniformly and then time division multiplexed. The sampling…

A: The lowest sample rate needed to accurately represent a signal without aliasing is known as the…

Q: 8. Which characteristic of IC in Digital Circuits represents a function of the switching time of a…

A: The solution is provided in the following section.

Q: 3. Which of the following is a key characteristic of orthogonal frequency-division multiplexing? A.…

A: This problem is based on the orthogonal frequency-division multiplexing. Which of the following…

Q: Identify the size for each of the following 8085 instructions:

A: In this question we will write size of instructions used in 8085 microprocessor....

Q: 8. Which characteristic of IC in Digital Circuits represents a function of the switching time of a…

A: Answer: d) Propagation delay Explanation: a) It is not a valid option. The Fan-out is the…

Q: (o11 An analog signal with a bandwidth of 4.2kHz is to be converted into binary PCM and transmitted…

Question

Find the BER of a 64-QAM system with SNR=10 dB. NOTE: Use Q-function table as needed.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Related to communication system
can you help me at least up to paragraph 3 or 4, please?
Pulse-code modulation (PCM) is the standard form of digital audio in computers, compact discs, digital telephony and other digital audio applications. Figure 3 shows the 3bit PCM system that transmit the 250 kHz analog signal with the voltage range from -6 mV to 6 mV. i) Identify the quantized value, voltage range and binary code for each level by building your own quantization table. ii) Calculate the minimum sampling rate and sampling time. ii) Identify the corresponding sampled voltage, the quantized voltage and binary code if the input signal is sampled at time t1 = 2us, t2 = 4us, t3 = 6us, t4 = 8µs. iv) Sketch the output in (iii) if it is fed to Manchester coding line encoder with bit rate of 20000 bit/sec and amplitude of +4 V. 5 4 3 2 10 Timel(usec) Figure 3 Amplitude (mV)
In a PCM system, the maximum frequency of the analog input signal is 4 kHz. If the number of quantization level of the uniform quantizer is increased from 2 to 8, then what will be the new transmission bandwidth of the PCM system?
The image added shows a digital modulator. State what the modulation scheme is and show how the modulated sequence 101 looks like if one bit contains three periods of the carrier sine wave, for the following types of modulating binary sequences: a) Unipolar b) Bipolar
Develop the truth table and constellation diagram of QPSK using I -channel reference cos wct and 90 degrees phase shift for IQ inputs 00 and 10. Draw the analog output waveform of the given inputs
3. Some GPS receivers use 1 bit ADCS (Analog-to-digital Converters) to sample and quantize the signal i.e. the output of the ADC is simply 2 quantization levels: -1 or +1. This is typically done to save on power. (a) What is the quantization SNR? How does it compare to typical thermal noise SNR of a GPS signal before correlating with the CDMA code? (b) Justify, how come it is possible to sample the signal using a single bit and still get good performance.
Problem 17. We are comparing to COTS ADCs (Commercial Off-The-Shelf Analog to Digital Converters). Unit A is a 10-bit ADC with ENOB = 8.6 bits. Unit B is a 9- bit ADC with ENOB 8.8 bits. What is the SINAD for Unit B? a. 50.528 dB b. 51.744 dB c. 52.96 dB d. 59.04 dB e. Not enough information
Explain the functions of decoders and multiplexers. Then given at least two examples of applications for both of them.
Choose the correct answer low HDOP (Horizontal Dilution of Precision) number such as2 indicates a ........................... a.poor fix b.good fix c.poor signal quality d. good signal quality
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?
Solve in digital format please In your words, describe what the signal modulation process consists of.