Find the armor size for preliminary design using the Hudson formula, for a rubble mound detached breakwater. The structure is in around 6 m water depth with a crest 2 m. The side slopes are set to 1V:2H. The breakwater length is 170 m. The design parameters are as follows: Crest level = 2 m; Seabed level = −6 m; Water level = 1 m Design significant wave height (non-breaking) Hs = (3,7) m Rock density = (2,64) t/m3, Stability coefficient = 2,8

Find the armor size for preliminary design using the Hudson formula, for a rubble mound detached breakwater. The structure is in around 6 m water depth with a crest 2 m. The side slopes are set to 1V:2H. The breakwater length is 170 m. The design parameters are as follows: Crest level = 2 m; Seabed level = −6 m; Water level = 1 m Design significant wave height (non-breaking) Hs = (3,7) m Rock density = (2,64) t/m3, Stability coefficient = 2,8

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the height of wave = 26.2467 ft, then the minimum depth between the lowest water level and the bottom of the break water= a. 7.99999 m b. 14.99999 m c. 5.99999 m d. None of the given answers e. 11.99999 m f. 6.99999 m
A concrete coated steel gas pipeline is to be laid between two offshore platforms in 100 m water depth where the maximum environmental conditions include waves of 20 m wave height and 14 s period. The pipeline outside diameter is 46 cm, and the clay bottom slope is 1 on 100. Determine the submerged unit weight of the pipe. Assume linear wave theory is valid and that the bottom current is negligible.
* Calculate effective strees at assigned depth RL= -1om. AsSume any value if necessary. RL = 0 0 m at the top De pth of waten = 8m. Density = 16.4 kNIm?.
A rectangular deck scow 23.50 m long, 7.10 m wide and 3.23 m high has a draft of 1.22 mwhen light and a draft of 3.05 m when loaded. The bottom length of the scow is 13.15 m. Thewaterline is 21.26 m long when the scow is loaded with rocks and 18.69 m long when light. Ifsea water weighs 1026kg/cubic meters and the loaded dredged material weighs 3208kg/cubicmeters, determine the volume of the loaded rock."
Troughs are 30ft long and width is 20% less than it length and one fourth of length is the measure to the center with horizontal flat bottom. The backwash rate is 24 in/min. Estimate (1) water depth of the troughs with free flow into the gullet, and (2) the distance between the top of the troughs and the 30-in sand bed. Assuming 40% expansion and 6in in free board in the troughs and 8 in of thickness.
Storm water from a housing area is discharging 10.8m/s and is designed to flow a trapezoidal section with manning's n= 0.018 and a bed slope of 0.0015. Determine the dimensions of the best hydraulic section (with 0.3 freeboard) if the side slope (on both side) is: %3D a) 45° b) 1(V): 1.8(H) c) Best section
Help me find the maximum and minimum pressure intensity.
Determine the sliding factor of safety and the heel and toe stresses for a triangle gravity dam (25m bed width and 20m height) with the following data: (neglect ice force and use e = 1.0m) 7 w=10 Kn/m³, 7 c-24 Kn/m³, s-1.8 Kn/m³, height of silt 2m, hw=0.5m, = 30° and free board 2m.
1.. How does the design of the apparatus enable the resultant-force on the- vertical surface to be measured? Are any significant forces be neglected? 2- Compare the theoretical and experimental values of (Wexpe) & (Wheo. ).Discuss any discrepancy? 3- What is the primary trend in yep-Yeg versus with water depth?
Question: Open channel test is performed and according to the following; (Q = 0.03484 m3/sn)( sill thickness = 2.5 cm) a) Find the critical depth b) Find Emin on the threshold y=6.6 cm 쇼 y2 = 1.6 cm Sill
A concrete coated steel gas pipeline is to be laid between two offshore platforms in 100 m water depth where the maximum environmental conditions include waves of 20 m wave height and 14 s period. The pipeline outside diameter is 46 cm, and the clay bottom slope is 1 on 100. Determine the submerged unit weight of the pipe. Assume linear wave theory is valid and that the bottom current is negligible. Please show all work done out numerically so it is easy to follow, thank you.