Find the amount ofenergyrequired tomove (6cJchnige from the origia top (sit,-inthe ficld E=2xax-3y?aj auê? alouge the Stright line path *=-32,ycX +zZ? ms -14J

Q: 38 mm diameter AB shaft, Gakma = 250 MPa Made of a strong steel. Using the maximum shear stress…

A:

Q: a. Find the position vector rac, express as a cartesian vector. b. Determine the moment of force…

A: Given data: F→=750i+650j−850k Nd1=0.9 md2=0.6 md3=0.4 md4=0.3 m

Q: O Mail - 9 Interval E Cock St O HW 20 O RedShe Co X A Faraday in engine M Your Tw O (236) SF O…

A:

Q: find rms of v(t), and average value Vde dc v(t) dT T.

A:

Q: Since the beam AB shown in the figure is P = 60 kN, L = 3 m and E = 200 GPa, find the deflection at…

A:

Q: Consider a simple supported beam subjected to the load shown. The beam has a solid circular…

A: Bending moment A bending moment is a measure of the bending effect that can occur when an external…

Q: Differentiate y = In- 1-x 3

A:

Q: Discuss why the τbrake value always larger compare to the τnet.

A:

Q: A mass, m of 22 kg consider one vertical motion only with angular displacement, 0 = wt, with spring…

A:

Q: The students reviewed the safety features of a bumper car and evaluated the features based on the…

A: 2. answers  Safety Features Function Bumper around entire car Reduces amount of force…

Q: 个り ÍRON CORE PROBLEMS 1) calculate the mayetomotive face 2) calculate the reluctance of thR System Z…

A: Hi ! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at…

Q: critical Find iTx) and! pressure critical tempreture Ai Az end Doto given Converging - Nuzze E 0:5…

A:

Q: Since the beam AB shown in the figure is P = 60 kN, L = 3 m and E = 200 GPa, find the deflection at…

A:

Q: of each resistance 96) Three identical coils , 102 and inductance 42mH are conected in star to va…

A: It is given as a 3 phase supply and so line voltage is 415 V Phase voltage can be found by:…

Q: What are the values of each variable? Show complete solution

A:

Q: Given'- u= 35mls V = om/s t-5secs S-2

A:

Q: Which one of these tables is least stable?

A: The answer for the given question is provided below.

Q: There is a hot water source in New Delhi.Our plan is to use this heat source for heating and hot…

A: The two organic fluids are - R600 - It is non-toxic, non-flammable and has a critical temperature…

Q: Determine which rigid body experiences complex motion Locate the instant center for that rigid body…

A:

Q: Find g f 150mm 120mm Ya loo 100 12omm 130mm

A:

Q: VY = 2xyz³ î + x²z³ j+ 3x²yz² & %3D Y(-2,1, –1) = 8 Find Y

A: Write the divergence of the function,   ∇→ψ=2xyz3i+x2z3j+3x2yz2k   Write the expression of…

Q: I need answers to parts 4, 5, and 6, pertaining to the print provided.

A: Yes, the given spring is ground end. From the drawing the end are grounded with closed end.

Q: fortheturss Showndetermih. the forces in mebers BGAB Hiand GI

A:

Q: = = 2 RA 2EI 2 0 2 3RA 2EI x² dx + kNm 2 RA 2EI 3 2 (x - 3)²dx

A: According to the given data  The Bending moment expression is given by the…

Q: why are you squaring the velocity in the eq

A:

Q: How does it integrate to get 5/56

A: It is asked to calculate the shear force in section AB

Q: 18 Modulus f elaeticity equal 2 times Bulk modeulus Find Poinson ratio

A: Consider the elastic modulus of the material as E. Consider the bulk modulus of the material as K.…

Q: Hanf written plzzz asap.plzz i'll rate sure

A:

Q: Roter ロ 9. Given: J= =, aco) = 300,t=los T=? Find torque=2 after t=10S time

A: given; →rotation of rotar (ω)=300rad/s→time(t)=10 sec→torque(T)=?→moment of inertia of rotar(J)=1

Q: Hinged at both ends. Find : (2. TcD = ?. (3) O LT=?

A:

Q: aY A twos tyoke Diesel engine has Six cglinders in-cine.thePiring orderis 4-3-2-3-6 .thecylinoders…

A: Given: The number of cylinder, n = 6 The distance between cylinders, x = 1.5 m The distance between…

Q: Heinz has claimed that it steam peals its tomatoes rather than using the chemical lye method. Let's…

A: Energy required to produce 50,000 lb/h of saturated steam for the process.   ** Heat required to…

Q: How do integrate to get fbd= 15/28

A: It is asked to calculate the shear force in the section BD

Q: Defoomine max: ofeay sforess ?

A: Given: state of plane stress at point is:  σx=220 MPa  σy=100 MPa   ζxy=130 MPaFor the data given,…

Q: I need answers to parts 1, 2, and 3, pertaining to the print provided.

A: (1)Locknut is a nut that resists loosening of nut under high vibrations and torque under loading…

Q: The moment of the UN wat pot measured cocks we equal 30° F = 400 N Ob 1988 Nm O 386 Nm acer

A:

Q: & Any suressive amfitudes ting yslem Can be used to determine the laganithmic decrement ccording to…

A:

Q: Determine the equations of the elastic curve for the shaft using the x1 and x2 coordinates. Take El…

A: Given: The moment in the end 'C', Mo=900 N-m

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.