Find resonant frequency and the bandwidth for the following circuit. (partial answer BW=2 rad/sec)

Q: is the most important segment and it contains the actual assembly language instructions to be…

A: microprocessor works based on the assembly lenguage instruction provided to it.

Q: Explain following: 1. Doubly Linked List 2. Circular Linked List 3. Insertion of an item in singly…

A:

Q: Explain the successive approximation type ADC with neat schematic diagram

A: We need to explain about succesive approximation type of ADC with a block diagram

Q: The register circuit is: O A. A storage device O B. A data selector O C. A code generator O D. None…

A: In this question they are interested in the definition of the register .     Generally registers are…

Q: (iv) 691 decimal to BCD (v) 796 decimal to hexadecimal

A:

Q: Problem Statement & Instructions: 1. State the resolution for each Digital Readout (DRO). 2. For…

A: RESOLUTION A measure of the sharpness and clarity of an image or picture is called resolution. It's…

Q: In IoT systems, actuators are responsible for transforming electrical inputs into actionable…

A: "Internet of Things" The term "IoT" refers to the "Internet of Things," which is a system of…

Q: Digital communication system can handle a) Analog signals b) 1D signals c) 2D signals d) All of the…

A: The correct answer is OPTION D

Q: Check following image ;then select : statement that correctly describe it

A: The explanation is as follows.

Q: You have used DEBUG to unassemble the following instructions. -U 0100 0108 1369:0100 B84365 MOV AX,…

A: The instruction DEC BX has the address 1369:0106, the given address consists of segment address and…

Q: 6- What is the difference between Software and Hardware interrupts?

A: Difference between Software and Hardware interrupts ?

Q: The information signal is always an analog signal. an analog signal in case of an analog carrier…

A: A signal can be in form of analog or digital signal.

Q: In FET, An outward-pointing arrow represents ___. Choose the correct answer below: a.N-type…

A:

Q: 5.164 20-4f 11₁₂=14001 pm a) If= 1.2.4 C 193 R₁=15-2 P=5KIJ-Pack

A: 5.16 P=4     RA=0.8 Ω   Vo=1.5 V n1=1400 rpm Solution- a) If=1.2 A  RL=15 Ω  PL=5kW=Pout   From…

Q: QUESTION 44 The 8259 is a O Low priority interrupt O Tristate buffer Programmable Peripheral…

A: Intel 8259 is a very important device and very commonly with 8085/8086 systems.

Q: An 8085 assembly language program is given below. Line 1: MVI A, B5H 2: MVI B, OEH 3: XRI 69H 4: ADD…

A: Given Assembly language program. We have to find the content of accumulator after the execution of…

Q: Q. No. 7: Determine the output of the following instructions and set/reset the values of the status…

A:

Q: Write a program that adds 5 bytes of data and save the result. The data should be following hex…

A: The given data is, DATA DB 25H,12H,15H,1FH,2BH    The required code is shown in the next step as,

Q: With neat diagram explain the principle of operation of Electrodynamometer type wattmeter. Digital…

A: Electrodynamometer is used for measuring the power of both the AC and DC circuits. its working is…

Q: Compare between the status and control flags? Explain the status flags for the operation AEH+37H ?

A: As per Bartleby guidelines we are allowed to solve only one question please ask the rest again. The…

Q: Draw a diagram so that data is loaded parallel and then it is shifted from left to right instead of…

A: Parallel Out data Serial in Data Registor Here we  use D flip-flop construction this type of…

Q: Design 4X1 mux using 2:4 decoder and tristate buffer. Draw circuit of D latch using mux

A: Latch is asynchronous device. It is level triggered device. Multiplexer is combinational Circuit…

Q: What does the data become after Quantization (remember to round the numbers)?

A: Quantization is used to convert continuous signals which are usually infinite to a set of finite…