Find out the outer diameter of the hollow shaft, if the allowable shear stress induced in it is 53MPa and the permissible value of Torque in it is 2000Nm. Take the value of k to be 0.6  k = the ratio of inner diameter to outer diameter.

Q: A solid 40 mm diameter shaft is subjected to the torques shown. The bearings shown allow the shaft…

A: To determine:The magnitude of maximum shear stress in the shaft()

Q: A motor driving a solid circular steel shaft transmits 40 kW of power at 500 rpm. If the diameter of…

A:

Q: A hollow bronze shaft (G=5000ksi) has an outer diameter of 3in and a wall thickness of 0.25in. The…

A: Given data: Converting all data into SI units. Modulus of rigidity G=5000 ksi=34473.8 Mpa Outer…

Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 6° in a…

A:

Q: The A-36 hollow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is rotating at…

A:

Q: The solid shaft (G=70 GPa) has a diameter of 40 mm. Calculate: a. The magnitude and direction of the…

A:

Q: The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate…

A:

Q: The outer diameter of the shaft is 100 mm and the diameter ratio is 1.25. Find the polar modulus of…

A: Outer diameter/ Inner diameter = 1.25.

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: A tubular steel shaft transmits a power of P = 450 hp at a speed of 3000 rpm. Determine the maximum…

A:

Q: A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the…

A: Given Data⇒ Line shaft rotating at (N)=320 rpm Power transmitted (P)=35 KW Allowable shear stress…

Q: The shear stress–strain diagram for a solid 50-mm diameter shaft can be approximated as shown in the…

A:

Q: A tubular steel shaft transmits a power of P = 450 hp at a speed of 3000 rpm. Determine the maximum…

A:

Q: A hollow circular steel shaft with an outside diameter of 2.569, and a wall thickness of 0.388 in.…

A: GivenPart 1D=2.569int=0.388inT=292 lb-ftL=124inG=12000 ksiPart 2D=2.915int=0.437inT=239  lb-ftL=105…

Q: A compound shaft consists of an outside tube (1) and an inner tube (2) that are fully connected…

A:

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: The given values are - do =75 mm, t=5 mm, T =4090×1000 Nmm, G =80×1000 Mpa, L=2000mm The inside…

Q: A hollow shaft of outer and inner diameters respectively equal to 0.6 in. and 0.2 in. is fabricated…

A: Torque required to twist the shaft is 20.525 lb-in.Explanation:

Q: Find the torsional shear stress on a 2 inch diameter shaft if it is subjected to a torque of 561…

A: Given diameter of shaft = 2 inch. Torque=561in-lb.

Q: Two designs for a shaft are being considered. Both have an outside diamete of 80 m and are 100 cm…

A:

Q: L1=1.8 L2=.9 d1=70 d2=53 Compound shaft ACB is fixed at A and consisting of two solid circular…

A: Given data:- The length L1 is L1 = 1.8 m. The length L2 is L2 = 0.9 m. The diameter D1 is D1 = 70…

Q: The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner…

A:

Q: The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the…

A:

Q: Compute the torsional shear stress in a circular shaft with a diame to a torque of 800 N-m.

A:

Q: A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is…

A:

Q: Determine the torque that can be transmitted by a shaft of 50 mm diameter, if the maximum allowable…

A:

Q: The dimensions of the cross section of an airplane fuselage are shown in figure 1. If the fuselage…

A: Given Data: The torque subjected to the fuselage is, T=8 MN·m=8 MN·m×1000 mmm=8×103 MN·mm. The…

Q: In the image below, B and C are pulleys. The belts on the pulleys exert the forces shown in the…

A:

Q: Determine the maximum shear stress magnitude in Segment (2). J1=

A:

Q: Calculate the torque T: i. if the shear stress of the brass sleeve in section AB is limited to τb =…

A: Shear stress is defined as the intensity of force acting on the cross sectional area. Shear stress…

Q: The copper pipe has an outer diameter of 2.5 in. and an inner diameter of 2.25 in. It is tightly…

A: Given data is

Q: If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa,…

A: allowable stress = 20 Mpa  Length = 0.75 m  Modulus of rigidity G =37 GPa

Q: A shaft of diameter 40 mm is subjected to 360 N-m torque. The length of the shaft is 10 cm.…

A: Given data: The diameter of the shaft, d = 40 mm. The torque subjected to the shaft, T = 360 N-m.…

Q: A circular solid shaft has a diameter of 60 mm and is subjected to a torque load of 8.7 kN•m.…

A: Given      Diameter, d = 60 mm  Torque load, T = 8.7 kN•m

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a…

A:

Q: A solid shaft is transmitting 15 MW of power at 1760 rpm. If the allowable shear stress must not…

A:

Q: A steel shaft with a length of 3.00 m. One meter of the steel is contained in a brass tube and…

A:

Q: Problem 1: A circular shaft with a diameter of 100 mm and a length of 2 meters is subjected…

A: Probelm 1. Diameter D=100mm , Length L=2m , G=80GPa , Torque T=500NmProblem 2. Diameter D=80mm ,…

Q: A drive shaft running at 2500 rpm has outer diameter of 60mm and inner diameter of 40mm. The…

A:

Q: A shaft is made of a steel alloy having an allowable shear stress of Tallow = 84 MPa. If the…

A: Given  : allowable shear stress , τallow = 84 MPa diameter of the shaft, D = 37.5 mm   To find : .…

Q: 8 in 5in 12 in S

A: