find moment, reactions, shear and bending moments. ( please, show all calculations with units, ) Chapter 5 Shearing Forces and Bending Moments in BeamsProblems for Figures P5-77 through P5-84Each figure shows a mechanical device in which one or moreforces are applied parallel to and away from the axis of themain, beam-like part. The devices are supported by bearingsat the locations marked with an x, which can provide reactionforces in any direction perpendicular to the axis of the beam.One of the bearings has the capability of resisting horizon-tally directed forces. For each figure, the objectives are thefollowing:1. Break the compound beam into parts consisting of eachof the straight components.2. Show the complete free-body diagram of each com-ponent part including all external loads and internalforces and bending moments required to keep the part inequilibrium.3. For the main, horizontal part only, draw the completeshearing force and bending moment diagrams. Refer toSection 5-10 for examples.Dimensions in mm-425- 250800 N150

Answered: Image /qna-images/answer/fe036885-04b4-4884-a8c5-bd906c70d08b.jpg

Answered: find moment, reactions, shear and…

Engineering

Civil Engineering

find moment, reactions, shear and bending moments. ( please, show all calculations with units, )

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw the shear and moment diagrams, then anwer the questions. The distance x is measured from point A to the right. 480 lb/ft 2.8 2.8'- Questions: At x = 0.9 ft, V = At x = 4.1 ft, V = B lb, lb, M = M = lb-ft lb-ft
Can you help me solve this problem with complete solution and free body diagram
If the vertical component of the force F applied to the ring is 10 lb, determine the magnitude F and also the horizontal component. F 300
A system of Forces is shown in the Figure. All length units are in meters. Determine the moment.
Please give me correct answer someone give wrong answers
Please answer attached image.thank you
Subject: statics of rigid bodiesshow your solution
Solve the problem and answer the questions that follow. - If the supports were swapped such that the left support were a roller and the right support a pin, how would your solution change? - If the value of “w” were doubled, what would be the bending moment at the left most point of the beam?
solve the following problem with step by step solutions so I can understand. please show all work
Determine the magnitude of the x-component of force Q (in N) if P=92.6 N, Q = 53.1 N, e = 58.8° and a = 42.2°.Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the x-component. Use R if to the right, L if to the left, U if upward or D if downward. y a
1 ft 3 ft B 3 ft 3 ft (-9002 + 800f + 1000k) Ib.ft 6 ft 3 ft E (-300î – 400ĵ + 100k) Ibs The applied force at point E and the applied couple moment at point D are shown in the figure. Complete/calculate the following: (Where applicable, express the results as the (x, y, z) components of a Cartesian vector) 1. Draw the free-body diagram (FBD), showing the appropriate reaction forces and/or moments at the supports. (You must show the reactions in their component form i.e. show RAx, MRAX etc. on the FBD). Note: The support at point A is not able to resist a moment about the 'X' axis but is able to resist a force in this direction. 2. The unit vector ÅBc 3. The position vector Tɛ/a 4. The position vector īB/a
Determine the values of F and P, if possible so that the force system shown in cases (b) through (d) are equivalent to the force system shown in case (a). F and P must maintain their direction as drawn. This is a problem where explanations will be critical to explain the logic you used. 12 kip |F 8 ft 4 kip 4 ft 4 ft 4 ft 4ft 4 ft 4 ft (a) (b) 2 kip 2 kip 2 kip (c) (d)