Find ix, iy and the Cabsorbed by) the 35V resistor poser dissipated by

Q: Sketch the DC load line for the fixed bias circuit and place the Q-point on it. ( !(a VCea) : (1.24…

A: Given

Q: 120 VRMS www Select one: OA. 300 mA OB. 150 mA OC. 48.7 MA OD. 50 mA OE. 16.67 MA OF. 100 mA OG. 200…

A: The circuit diagram,The current in secondary,

Q: Set up a midpoint bias for a JFET with Ipss = 14 mA and VGs(off) =-10 V. Use a 24 V dc source as the…

A: It is given that: IDSS=14  mAVGSoff=-10VVDD=24 V

Q: You are working as a hardware engineer in an R&D department and your new task is to design a voltage…

A: Note: As per our honor code, we are authorized to answer only  3 sub-parts, we’ll answer the first…

Q: The voltage regulation can be equal to zero when: O The t and current is not too high. OThe p.f. is…

A:

Q: Question 2 (a) Briefly explain the need for power factor correction (PFC). (b) Briefly explain how…

A: A)Power factor correction (PFC) mainly aims to improve the power factor along with the power…

Q: Vác= 150 V V, (ms) = 15 V V'. de V', (rms) R 500 2 Full-wave rectifier C, 15 μF C2 10μF RL 5 k2

A: Introduction: Full wave rectifier is circuit, consists of two diode. Full wave rectifier operates…

Q: the

A: In this we have to write about half adder...

Q: 1. Let us plot the Shockley diode equation. Suppose you are required to use In () as the vertical…

A: Intrinsic semiconductors have very low conductivity at the room temperature. Hence, extra charge…

Q: Find the voltage across and the current through each resistor using superposition. R1 = units |R2 =…

A: In this question,  We need to determine the current in the each resistances and voltage across them.…

Q: b. Snubbers are an essential part of power electronics to protect the active devices. Design a…

A:

Q: Find Z₁, Z₂ and i(t). 3Ω ww 3.2 mH Z₁ L 2 100μF 80 Hem 22 100 cos (1250r) V

A: As per our company guidelines we are supposed to answer only first question kindly repost the other…

Q: Using Y-A or A-Y transformations, determine Rab 40 80 20 08. ww

A: The ∆-Υ and Υ-∆ transformation can be done as:

Q: A) CALCULATE THE VALUE OF THE LOAD RESISTANCE (RL) SO THAT ITS POWER IS MAXIMUM.  B) WHAT WILL BE…

A:

Q: find the AC module & voltage gain using pi module

A: Given the circuit: We need to draw the ac equivalent circuit and we need to find the voltage gain…

Q: :- Mention at Jeast three plostion practical applicationihere ASkı FSK used and Psk Techniques Care

A: ASK, FSK and PSK are digital modulation techniques, where digital signals are used for career…

Q: Please find Dc componet values

A:

Q: Solve for the output voltages.

A: Referring to the given circuit, the voltage at the non-inverting terminal is zero. By the theory of…

Q: Compute for the Vo regarding with the figure.

A: A Light Dependent Resistor (LDR), also known as a photoresistor, is a type of resistor whose…

Q: Find the IT in circuit * It 5R VT loov O 100 V O 10 A 13.33 C/S O 13.33 J/S

A: Given,

Q: Which of the following is true about JFET? The gate is grounded B The gate to source PN junction is…

A: 1. Which of the following is true about JFET ? A. Gate is grounded  B. The gate to source PN…

Q: please help me make this into a hybrid pi model.

A:

Q: Do the following: a.)Convert 0.7692*10-9 Hz into Mrad/s b.)Convert 22*10-9 Hz into Grad/s

A: In thses question, Frequency w= 2πf  rad/s Where f frequency in Hertz.  a.)Convert 0.7692*10-9 Hz…

Q: For a voltage divider JFET

A: JFET- Full form of JFET is Junction Field Effect Transistor it the simplest form of field-effect…

Q: Explain what each component is in the design below: D 7Ro 21 -Q5 8Eo- 4 9 So 10 - type of circuit?…

A: In digital system flip flops are very commonly used components , they are sequential circuits that…

Q: With the help of VBB source, adjust the IC current to 5mA by increasing the IB current. To this…

A: According to question: The value of voltage 'VCE' is calculated as…

Q: In the circuit given in the figure | VBE | = 0.7V, R1 = 17.07Kohm, R2 = 64.82Kohm, RC = 1.49Kohm, RE…

A:

Q: The circuit of Figure below uses current- (or shunt-) feedback bias. The Si transistor has ICEO = 0,…

A: Kindly mention the condition which will change after connexcting Re as operating point will shift.

Q: Repeat the design using TFF by making the state diagram of the circuit given below.

A: The Logic Circuit is: Given, D1=C3'=Q3' Let the initial state of all the flip flops be,…

Q: Stringing of cells in a PV panel Draw the tabbing and bus-bar wires for a 72 cell module using three…

A: Given: Stringing of cells in a PV panel. To find: Draw the tabbing and bus-bar wires for a 72-cell…

Q: Q-4. When VGs of a JFET changes from -3.1 V to -3 V, the drain current changes from 1 mA to 1.3 mA.…

A: Given JFET The VGS changes from -3.1 v to -3 v The drain current changes from 1 mA to 1.3 mA

Q: A stabilization circuit has a stability factor of 0.04 and an internal resistance of 5 22. The…

A:

Q: Which of the following is true about the D-type MOSFETS?

A: In the depletion MOSFET (D-MOSFET), the conducting channel is already present between the source and…

Q: Des:gn the neturk to maintain Lat 12v. for load variation IL from ComA to zoumA) Defermine Rs and Va…

A:

Q: Draw the small signal equivalent circuit of the following circuit. Note that C1 and C2 are large AC…

A: We need to draw small signal model for given circuit .

Q: Find the current phasor through the inductor 102 -5jn 1020°V 10260°V

A: