Find each of the following in rectangular (a + bi) form if z 2-3i; if z =+ iy. 1 19. 20. 21. 2+1 1+: 22. 23. 24. /3

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: QUESTION 58 The inner cone of the flame has the O Highest O Coldest O Moderate O Lowest temperature.

A: The inner cone of the flame has the highest temperature.. Because this temperature (3500°c).the…

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: Draw the front, Side and top

A: We need to draw three orthographic projection views.

Q: why is the angle 26.56 and then you use 22.56

A:

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: The first moment of an area (mm3) about the x-axis (Qx) is O 462,000 O 594,000 O 246,000 864,000

A:

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: how does the angle alpha make the angle with t

A: This question is based on the concept of force and Free body diagram

Q: is 60 left or right?

A: The horizontal reaction at A: 60 kN (Right)......(Option D)

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: Calculate the linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

A: To find - The linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

Q: Mercury has a uniform coefficient of expansion Select one: O True O False

A:

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: Generally, the triangles can be divided into two kinds; right angle and not right angle. * O True O…

A: It is true that the triangles can be divided into two kinds; right angle and not right angle.

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: B: From figure 1, draw and explain the meaning of present symbol.

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: Question No. 5 Find out the missing number in the series given below: 6, 13, 28, 59, ?, 249 O 124 O…

A: here, (6×2)+1 =13 (13×2)+2= 28 (28×2)+3 =59 (59×2)+4 = 122 (122×2)+5 = 248

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: Why cos(60 if I don't see that angle in the figure

A: This question can be solved by labelling angles.

Q: The design below is used for a bridge construction. All parts of the assembly are made of ASTM A36…

A: P = 4000 lbOD = 4.5 inL =20 inTo find : Minimum size of weld according to table 20-4

Q: what is the ybar distance(distance from bottom edge of triangle to centroid)?    options:   40/3…

A: Given, Right-angled triangle of, Base, b=20 in Height, h=9 in

Q: if the bullet that hit the cashier made a bullet hole that was 3 mm wide and 8 mm long, white was…

A: Given data:

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: Draw the front, Side and top

A: According to the question we need to draw the three orthographic projection views of the given…

Q: Top View Front View Right side View

A: according to the given details in the question, the Drawing of the figure is shown below. as…

Q: A good electrode holder in arc welding should be Weak insulation to protect against accidental…

A: Hi and thank you for the questions. Since you have asked multiple questions, we will solve the first…

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: Isn't the area of the circle equal to pi times the square of its radius?

A: Explanation: Since the diameter ( d )  of steel bar is given, area of the circle is in terms of…

Q: PLease draw the top view and section view with dimension of the figure

A: Here is Top View and Section View of figure with well dimensioned.

Q: Draw the orthographic Projections of given object.

A: Orthographic projections are projections of a component in three directions that are perpendicular…

Q: Why does changing the gun angle affect the weld?

A: The gun angle is kept a few degrees lower to avoid the filler metal from rolling out on the weld and…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.