Find and plot the spectra of each of the following waveforms. $3(t) 2 1 1 1 -1 -1 s2(1) 2 1 4 1 2 3 -2

Q: Once the LED turns on, it then has a constant forward voltage across it. Once this accurs, what kind…

A: LED is  special type of diode. Resistance of the diode comes into to picture due to the depletion…

Q: Design a circuit and write an Arduino code to displays "5 seconds elapsed" and blink an LED every 5…

A: It is asked to design a circuit and write an Arduino code to displays "5 seconds elapsed" and blink…

Q: 'JQ Clock J clock K

A:

Q: . When making a high energy measurement: a. Attach the meter to the energized line first, then to…

A: 9) High energy measurement

Q: B. (a) Find Peak time CTP), Percent overs hoot (00os), setting time CtS), Rise Time CTR) of 3.1416…

A:

Q: Draw a simple pulse detector (positive-edge) diagram and explain how it works.

A: The edge detector circuit generates a positive spike at at the positive going or negative going edge…

Q: Modulator is a term used to describe any device that converts signals.explain

A: For the wireless transmission of the signal, the signal message signal must be amplified and must be…

Q: 6 What is the relay and what are its two circuits?

A: to know about the relay.

Q: The figure below shows a loạding truck in a cement factory. The truck has three wheels, front wheel…

A: According to the question, we need to design a control circuit by using a multiplexer that operates…

Q: by using third order MEV method and K-map and write the logical expression, draw the circuit The…

A: The circuit is drawn as shown below

Q: Has anyone taken and or has any pointers on taking the industrial electricity NOCTI # 2050.

A: As per the NOCTI Job ready credential blueprint version:01, following points can be followed.…

Q: lect all correct answers. elect one or more: Da The figure consists of 2 loops. Ob. The figure…

A: to select one or more correct answers a) the figure consists of 2 loops b) the figure consists of 1…

Q: A circuit has two pushbutton switches connected to pin PB2and PB3 and two LEDs connected to pin PC0…

A:

Q: Could someone explain the solution picture 1 with the 'OR'. The solution is on picture 2 but I want…

A: According to the question, for the given circuit as shown below We need to explain the problem…

Q: A speedometer is connected in an automobile system to measure the speed. The meter reads 120.8 rpm…

A: In this question we need to choose a correct option

Q: 3.Explain the positive clipping operation with circuit diagram and Waveforms.

A:

Q: 1. Observe the physical parts of the analog trainer   2. From your observation list down the major…

A: Electrical devices are used for measuring electrical parameters. Current, voltage and power are…

Q: 21. Which voltage range that is sometimes called a “float" in TTL circuits?

A:

Q: Crystal radio receiver Please explain how this circuit works

A: NOTE- According to the policy, we can answer only one question, please post other question as…

Q: of the following statements is true for an SCR. It is an on-only controllable switch, which is…

A: There are three types of switches: Uncontrolled switches : In these turn on and turn off can not be…

Q: In a signal phase, pedestrians are allowed to cross the street walking in the same direction as…

A: It is given that: Crosswalk length=L=722 ft=36 ftWE=9 ftWE<10 ftδp=4 ft/secNpld=20

Q: Q.26 Why is shielded wire used for signal runs? Select one: A. TO PREVENT VOLTAGE SPIKES B. TO…

A: From this question we need to know why we use shielded wire for signal runs :

Q: List two important uses Loop (PLL) in of phase locked analog Communication System.

A: PLL can be used as AM detector for demodulating amplitude modulated signals. Main goal of a PLL is…

Q: There are a number of importance of measurement and instrumentation system. Identify and explain 5…

A: importance of measurement and instrumentation system: Product development: Measurement and…

Q: X) Answer the following questions  (a)What is a clock signal? (b)Differentiate between positive…

A: a) Clock signal refer to a type of signal that oscillates between a high and a low stste and is…

Q: Can We usẽ a non-conducting tip STM? EXplälh your answer.

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Q: 4.) Why is thermal noise sometimes called white noise?

A: White noise: It is a random signal having same intensity at different frequencies. Its power…

Q: Horizontal Controls Autoset tical Controls Trigger Controls

A:

Q: How does increasing the temperature of component affect its noise power?

A: FIND: how does increasing the temperature of component affects its noise power

Q: what is the STOP W.O.K.E Act

A: Florida state legislature, with the support of Republican Government- ‘Ron DeSantis’. passed a new…

Q: Why switching circuits are called as finite state systems

A: In this question we will write about why switching circuits are called as finite state systems.....

Q: A Single Phase 220V.2KW Heater is connected across a Single phase 60H S SCR For firing delay of 600.…

A: The RMS value of the applied voltage applied and output current can be calculated as: Vor=12π∫απ(Vm…

Q: What is analog switch?

A: An analog switch is also known as bilateral switch which is similar to relay with no moving parts.…

Q: A motor device is labeled 150 mFd. This device is a

A: This question belongs to electrical machine . It is based on the concept of unit of devices .

Q: IV- Define with draw the block diagram the sensor fusion.

A: Sensor fusion aims to overcome the limitations of individual sensors by gathering and fusing data…

Q: DESCRIBE THE PURPOSE OF MULTIPLIERS IN SERIES & SHUNTS ACROSS A METER MOVEMENT.

A: SOLUTION MULTIPLIERS                        Multipliers are used to…