Fill the blanks in the following statements about HMA construction. a) In a paver the receives HMA from the conveyor and spreads it out evenly over the width to be paved. The paver provide compaction between and percent of maximum density. b) In cold weather paving the Available for compaction is limited because HMA rates increases.

Fill the blanks in the following statements about HMA construction. a) In a paver the receives HMA from the conveyor and spreads it out evenly over the width to be paved. The paver provide compaction between and percent of maximum density. b) In cold weather paving the Available for compaction is limited because HMA rates increases.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

After 2 years of traffic, cores were recovered from the roadway whichhas severe rutting and bleeding. The bulk specific gravity and the maximum theoretical specific gravity were measured on these cores and are asfollows:Bulk specific gravity = 2.487Maximum theoretical specific gravity = 2.561 a. Calculate the air voidsb. If the design air void content was 4%, explain what effect the calculatedair voids had on the rutting and bleeding noted.
A truck is hauling earth from a construction site. The truck has the following specifications: Maximum allowable gross vehicle weight 37,800 lb Empty vehicle weight 10,800 lb Heaped capacity 12 yd 10 yd Struck capacity Haul time to dump area, including load, haul, return, and dump times 17 min Delay time 5 min/hr The soil has the following characteristics: Bank density Loose density 110 pcf 100 pcf The productivity, in bank measure (yd/hr), of this operation is most nearly: 38.8 (В) (C) (D) 35.3 32.3 29.5
A paving mixture is prepared for surfacing a section of highway as follows; AC-20 asphalt cement, Gs=1.05, total content =6 % by total weight of mixture. Combined aggregate (bulk G) = 2.65, MaxGm=2.5, Marshall density = 2.458 gm/cm³. Determine the relative compaction of pavement necessary for providing VFA-70%. A
I need the answer as soon as possible
22. Calculate the compacted cubic yards per hour if a com- pactor with a 5-ft drum width travels at 3 miles per hour over a 10-in. lift of aggregate base course with 4 passes required to meet density specifications under average operating conditions.
Q2/ Answer 5 of the followings by choosing the correct answer. 1- The shrinkage in the soil is always accompanied by: A. Increase in the soil density C. Decrease in the volume of soil 2-If the engine with 200hp, consumption factor is: A. 0.7 B. 0.8 C. 0.9 D. 0.6 3-If the contract was assigned according to the traditional method and the employer finds that one of the subcontractors has some errors in his work, it is better here for the employer to: A. Notify the subcontractor of the errors to correct it within time. B. Stop the work of subcontractor to make corrections. B. Decrease in the soil porosity, D. All of the above of diesel is 14.4 lt/hr, and the engine factor is 0.6, then the time C. Notify the main contractor of the error to take the necessary action. D. Making a deduction from the cost according to the size of the error. 4- It is better for a contractor to invest in owning construction equipment when the other option has: A. Better productivity or less time. B. Better…
1. You stumble and break your leg after falling into a deep pot hole. While waiting for your leg to heal, you decide to fill in the pot hole with some gravel so no one else gets hurt. You go to the garden store to buy gravel but no one has heard of the USCS system. That does not matter since they only have one type anyway. You buy a bag and run a sieve test on a 470g sample that produces the following data. Plot the grain size distribution curve, identify the coefficients of curvature and uniformity, and classify according to USCS. Explain why either a poorly graded gravel or a well graded gravel would be better for this application (hint: think about the voids). Sieve size (mm) Mass retained (g) 63 0 26 37.5 19 28 13.2 18 9.5 6.7 4.75 2.36 1.18 0.6 0.212 0.075 20 49 50 137 46 31 34 30
- Once answered correctly will UPVOTE!!
Material Specific Gravity Weight (g) Bulk specific gravity Coarse 2450 2.69 Aggregate Fine 1270 2.58 Aggregate Filler Asphalt 120 2.47 1.05 4% cement
Answer the following questions: 1. 250 cu.m-Column, 185 cu.m-concrete pavement, how many samples? And what type of sample? 2. 750 lengths of Galvanized Steel Pipes, how many samples should you submit for testing and how much? 3. If you have 450 drums of asphaltic material, how many samples and how much should you submit for testing? 4. You have 25,000 units of CHB, how many samples should you submit for strength determination only? 5. Formworks for Beam with 3,500 psi to be removed after 14 days with a strength of 2,900 psi, would you allow or not? Why? Reference: DPWH Standard Specifications for Public Works and Highway (2004 edition), Volume II
i need the answer quickly
The field capacity of waste decreases with overburden pressure. True or false and why?