Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P₁ P₂ B C D 500 mm +250 mm-++-350 mm +250. A ANSWER: IN D.

Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P₁ P₂ B C D 500 mm +250 mm-++-350 mm +250. A ANSWER: IN D.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel column with an outer diameter of 50 mm and an inner diameter of 40 mm surrounds a solid steel bar with a diameter of 30 mm. A support at one end of the bar and a hard plate at the other end of the tube hold them both tightly in place. A torque T = 650 Nm acting on the end plate twists the composite bar, which has a height of 850 mm. Assuming that the steel's shear modulus is G = 80 GPa, find the maximum shear stresses in the bar and tube, respectively, and the angle of rotation (in degrees) of the end plate
The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap D= 4 mm between the lower end of the left rod and its pin support at C. Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm2 for rod BD. Use E= 200 GPa for steel. lo/0 0.75 m 1.5m 2 m ANSWER: MPa
The bronze bar 3.42 m long with a cross-sectional area of 627 mm2 is placed between two rigid walls. At a temperature of -14 °C, there is a gap Δ = 2.36 mm, as shown in the figure. Find the temperature at which the compressive stress in the bar will be 34.22 MPa. Use α = 18 × 10-6 /°C and E = 80.32 GPa. Round off your answer to two decimal places.
Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. A parameter value units 470 mm 400 mm 40 mm 30 mm 30 KN cc 080 BY NO SA 2021 Cathy Zupke L₁ L2 d₁ d₂ P 4₁ B C E The stress in AB σAB= The stress in CD and EF: OCD = EF= d₂ L₂ MPa D F MPa
QUESTION 2 The rigid bar ACE is supported by two steel rods AB and CD (Esteel = 200 GPa) with the cross sectional areas of each rod is given as shown in Figure Q2. (a) Determine the position d of the 30 kN load so that the average normal stress in each rod is the same. (b) Find the strain in rod CD, ɛcD (c) Determine the horizontal displacement of point E 1.2 m ACD = 600 mm? 0.8 m E 30 kN AAB = 900 mm2 d B 1.8 m Figure Q2
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 30 kips, F₂ = 14 kips, F3 = 20 kips, and F4 = 39 kips, determine the absolute value of the axial load in rod (2). EVOVE F3 (2) (3) A O 24 kips O 18 kips O 21 kips 28 kips O 17 kips B F3 F4 C D
If the flat link shown below has an allowable tensile stress of 75 MPa, then a force P 1800 N will require the link to have a minimum thickness of: 30 mm 10 mm 3.20 mm 2.60 mm 2.40 mm 2.20 mm 3.60 mm 3.00 mm 2.80 mm O 3.40 mm
Let's consider a rod having a solid circular cross- section with diameter of 4 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: F = 3427 N F = 2856 N F = 5712 N F = 8568 N F = 7140 N F = 2285 N
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. I Determine the tensile stress in each rod. Determine the shear stress in pin A between the members. If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint. 40 mm 5 kN. 30 mm 25 mm 5 kN
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 31 kips, F₂ = 11 kips, F3 = 22 kips, and F4 = 36 kips, determine the absolute value of the axial load in rod (2). F A F₂ (1) F₂ B F3 C (3) D O 16 kips O 12 kips O 7 kips O 9 kips O 22 kips
1. Steel rod 2.5m long is secured between tow walls. If the load on the rod is zero at 200C, compute the stress when temperature drops to (-200C). The cross-sectional area of the rod is 1200 mm2 α=11.7μ m/(m.0C) and E=200 GPa. Solve assuming (a) that the wall is rigid and (b) that the wall spring together a total distance of 0.500mm as the temperature drops. 2. The rigid bar ABC in Figure is pinned at B and attached to the two vertical rods. Initially, the bar is horizontal and the vertical rods are stress-free. Determine the stress in the aluminum rod if the temperature of the steel rod is decreased by 40°C. Neglect the weight of bar ABC.