Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive load of 250 kN. The section dimensions are breadth, b = 0.12 m, depth, d = 0.05 m with an equal thickness on all sides, t = 0.003 m. Calculate the compressive stress σ in the tube. Give your answer in N/mm2 to 2 decimal places

Q: Q2: For the element shown in Figure 2. Use the data from Table 2 Determine the following: 1. The…

A:

Q: Mohr's Circle At a point, the major principal stress is 80 psi compression and the minor principal…

A: Givenσp1=-80psiσP2=-20psi

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A:

Q: he stress condition given in the figure, find the approximation o

A:

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A: Given data wire diameter (d) = 5 mm  OD of coil = 60 mm active coil = 12 Permissible shear stress =…

Q: The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the…

A:

Q: mm in diameter has a tensile load of 40 kN. Find the average tensile stress   at the section M and…

A:

Q: A rod of different materials is arranged as shown with the corresponding axial forces (see figure…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S = 75 MPa and Sy =…

A:

Q: 1. Question: With a pin on the AB beam A and a short lever BC as shown in the figure is supported.…

A: Given dataDiameter of the pins ar A,B and C d = 18mmLoad P = 30kNAngle α= 600Pin =ADetermine the…

Q: 20 mm- 50 mm 20 mm 100 mm 50 mm 100 mm M-8 kN-m A unique strut, shown in the figure, will be used in…

A:

Q: as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane…

A: Given: The diameter of the shaft, d = 20 mm = 0.02 m

Q: The internal loadings at a section of the beam in Elouce.1) are shown Figure 100 mm 0 mm 200 mm 10…

A: Given: Fx=-80 kNFy=60 kNMy=500 N.mMz=10 kN.m=10×106N.mm

Q: The eyebolt shown in Figure below, the allowable shear stress for the supporting material is Tallow…

A: Given data Allowable shearing strength=48MPa

Q: 1) The steel tube in the system below has an outside radius as listed and an inside diameter of…

A:

Q: Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension),…

A:

Q: 1) For the data given below, calculate the minimum value of the thickness of the object in the…

A: Given: The maximum allowed normal stress = 400 MPa The maximum allowed shear stress = 240 MPa The…

Q: as -ja-A Find the approximate prime plane in dogreos for the state of st given in the figure. 45 MPa…

A:

Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…

A: Given     Outside diameter, d2 = 0.8 in        Inside diameter, d2 = 0.19 in…

Q: The stress at a point of a machine component are 200MPa tensile and 100MPa compressive. Using Mohr’s…

A: Given: σx=200 MPaσy=-100 MPaτxy=0θ=30°

Q: 3 please help Provide Free Body Diagram, labeled with appropriate quantities to better understand.…

A: σ1=156.84MPaσ2=33.153MPaandθ=37.98°Explanation:

Q: 1. As a section cut in a prismatic bar varies from 0 = 0° to 180° at what values of 0 will the…

A: To find:

Q: The state of stress at a given point is given in the following figure. Use Mohr’s circle to find: a)…

A:

Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…

A:

Q: 1: The forces as given below are applied as shown in the figure. Fi=10 kN, F2=5 kN and F3=3 kN. The…

A:

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A:

Q: ss in the pipe is 2.50 kN/mm², calculate the minimum wall thickness required for the pipe. Give your…

A: The Inside diameter of the pipe, (di)=42 mm. The axial load on the pipe,(P)=850 kN. The allowable…

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A: Data given-  d = 5 mm  Do = 54 mm  n = 16  Permissible shear stress = 335 N/mm2  G = 82 kN/mm2

Q: section shown in figure Question 2, determine the shear stress a. In the Web at point A b. and in…

A:

Q: A helical spring used in an automobile suspension is having a wire diameter of 6mm and an outside…

A:

Q: A steel panel is subjected to a compressive loading in order to improve the panel stiffness and to…

A: Given:- F=400kips V= 0.20 E=2.8x107psi

Q: In the figure below, A 50 mm shaft is subjected to a reversed load P= 2700 N. Find the length (L),…

A:

Q: Q2: For the rigid slab shown in figure, find the total elongation in steel rod if the temperature…

A: Given l=4m∆T=40°CA=250 mm2E=200 GPaα=11.7×10-6 /°C to find total elongation of stell rod…

Q: The 1x3 piece of lumber shown was manufactured with the grain of the wood aligned at an angle = 10°…

A:

Q: Two identical plates are connected by two 25-mm diameter rivets as shown. Consider the following…

A:

Q: 2. A researcher plans to test a thin sample of a biopolymer under planar loading. Prior tests have…

A:

Q: The tensile stress in the AB bar is in the BC bar in order for it to be the same as the pressure…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.