Figure Q1-1 shows a partially sectional view of a bevel gearbox. Thevertical and horizontal forces (Fy and FH) are indicated at the meshing pointof the pair of the bevel gears. Due to the loading condition of the bevelgearbox, certain amount of linear and angular deflections of the input shaftare expected.i)Which types of rolling element bearings would you choose for bothsides (LHS and RHS) to support the input shaft of the gearbox andbriefly explain why?ii)What arrangement would you use to ensure appropriate arrangementof the chosen bearings?LHS BearingRHS BearingFvFHInputshaftFigure Q1-1

Bevel Gear The pitch surface is shaped like a cone, and the teeth are cut along the cone. This is…

Figure Q1-1 shows a partially sectional view of a bevel gearbox. The vertical and horizontal forces (Fv and FH) are indicated at the meshing poit of the pair of the bevel gears. Due to the loading condition of the bevel gearbox, certain amount of linear and angular deflections of the input sha are expected. i) Which types of rolling element bearings would you choose for both sides (LHS and RHS) to support the input shaft of the gearbox and briefly explain why? ii) What arrangement would you use to ensure appropriate arrangemer of the chosen bearings? LHS Bearing RHS Bearing Fv FH Input shaft Figure Q1-1

Figure Q1-1 shows a partially sectional view of a bevel gearbox. The vertical and horizontal forces (Fv and FH) are indicated at the meshing poit of the pair of the bevel gears. Due to the loading condition of the bevel gearbox, certain amount of linear and angular deflections of the input sha are expected. i) Which types of rolling element bearings would you choose for both sides (LHS and RHS) to support the input shaft of the gearbox and briefly explain why? ii) What arrangement would you use to ensure appropriate arrangemer of the chosen bearings? LHS Bearing RHS Bearing Fv FH Input shaft Figure Q1-1

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Use at least 4 significant figures throughout the entire problem. 9.80m/s2 for the acceleration due to gravity. Do not use 10 m/s2 for the acceleration due to gravity.
A horizontal 810-N merry-go-round of radius 1.20 m is started from rest by a constant horizontal force of 55 N applied tangentially to the merry-go-round. Find the kinetic energy of the merry-go-round after 4.0 s. (Assume it is a solid cylinder. Also assume the force is applied at the outside edge.) 263.99 Your response differs from the correct answer by more than 10%. Double check your calculations. J Need Help? Read It
Refer to the question below.
A turn table starts from 10 rad/s of angular velocity and slows down to a stop in 5.0 s. Find the total angle turned during this time, in rad. Hint: use rotational kinematics formula. Assume initial angle and final angular velocity as zero.
In part b) the moment which is in red color why doesn't equal -T( AP + Radius ) since they are perpendicular. Why did he use the components of T
Needs Complete typed solution with 100 % accuracy.
Needs Complete typed solution with 100 % accuracy.
A long, thin uniform rod of length 1.29m and mass 2.08kg is pivoted about a horizontal, frictionless pin passing through one end. The rod is released from one end in the vertical position. L y Pivot x At the instant the rod is horizontal, find its angular speed. Submit Answer Tries 0/10 At the instant the rod is horizontal, what is its angluar acceleration? Submit Answer Tries 0/10 At the instant the rod is horizontal, what is the magnitude of its x-component of acceleration at its centre of mass? Submit Answer Tries 0/10 At the instant the rod is horizontal, what is the magnitude of its Y-component of acceleration at its centre of mass? Submit Answer Tries 0/10