Figure out the 2D sketch of bracket using AutoCAD and mention all the dimensions. Colour the hatched lines which are inside the curve 2 holes 22 Dia 46 NOR 0F

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: 38 17 Hole Tam delik 18 19 20 20 8 26, 20. 89

A: Given:-

Q: Find the velocity of point B and angular velocity in link 3 using relative analysis and polygon…

A: The angular speed of link O2A is ω2=1 rad/s The length of the links are…

Q: ab) What is the composite area's moment of inertia based on axis Yo?

A: we have to determine the MOI

Q: For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm and Gear D is the…

A: Find the angular velocity of gear D.

Q: v) w) What is the distance, dsy, of shape 5's centroid from axis Yo? What is the distance, dzy, of…

A: (v) Consider the shape 5 and calculate the distance, d5y, of shape 5's  centroid from axis y0.

Q: draw the orthographic view of the drawing and identify the alphabets of lines used by pointing out…

A:

Q: Draft and annotate the 2D sketch of housing using AutoCAD and mention all the dimensions. Colour the…

A:

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: For question 5, this is my way of calculate wheel A and B to find is the component will fail is…

A: Given: To find: Whether the components are safe

Q: For the compressor shown in the following figure, find the position of the piston with respect to…

A:

Q: Briefly describe the action taken by the following G&M command blocks assuming absolute coordinates.…

A:

Q: Write

A: The spindle speed of machine is, N = 1800 rpm. The feed rate is, f = 3 mm/min. The depth of cut is,…

Q: Draft and annotate the 2D sketch of support using AutoCAD and mention all the dimensions. Colour the…

A:

Q: Apply geometric tolerancing to part according to the instructions below. This exercise will provide…

A: The majority of current production techniques and equipment are incapable of producing items that…

Q: The given sketch is a view of modified “Plate" one view. Sketch the 2D sketch of the below figure…

A:

Q: Draw, using 1 st angle projection Orthographic view of the following figure  with  suitable scale,…

A: (a) the given front elevation;

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: 30r 20dls 20 10r 20 20 30 150 100

A:

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: Given the isometric drawing of the solid, draw the multiview projection.

Q: Answer the following in the space provided. 39. Suppose the engine in a vehicle is delivering 550…

A: Data given-  T1 = 550 lb -ft  N1 = 5000 rpm  Gear ratio = 1.5/ 1 = 1.5

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: SKETCH THE 2D FIGURE IN AUTOCAD DRAWING AND USE THE 2D SKETCHING TO FIGURE OUT THE BELOW SKETCH

A:

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0  ,  Y =74   ,   Z =…

Q: Create the 3D Model of the Shaft Holder Produce Drawings: 1. Isometric 3D Shaded 2. Detail Drawing:…

A: Given Model To find Isometric 3D Shaded Front view Top View Full Sectional Left Side view

Q: Creste an sometre ptora and thena caet ut l the folloing abject. The grid soacing is 10 mm.

A:

Q: Draw velocity polygon.

A: Solution:

Q: A. Find the value of tapered angle (a): Answer:

A: Find    The value of Taper angle

Q: 03: Write two G-code programs using the following figure where units are in inch a. The first…

A: What is G code:- G code is a programming language largely used for operating Computer Numerical…

Q: The given sketch is a cross section view of bracket. Sketch the 2D sketch of the below figure using…

A:

Q: Write the types of keys and sketch freehand of them with dimensions and equations.

A: A key is a machine element that is fitted in the axial direction with the mating parts in pulleys…

Q: A person is pulled to the right on a sled (total mass of 53.3 kg) across the surface of a frozen…

A:

Q: Draft and annotate the 2D sketch of upright using AutoCAD and mention all the dimensions. Colour the…

A:

Q: Consider FIG-DD in the appendix.   Note: For Blocks “A” & “B” & “C”: The mass of “A” is 30 kg.…

A:

Q: 1-autocad drawing for multispendel nut runner

A:

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: Draw the following shapes using AutoCAD 2017

A:

Q: Find the number of rotations of wheel 3 in rotations per minute (rpm) wile the load A is moving down…

A:

Q: What is the radius size of the arc programmed in the following CNC codes in absolute coordinates…

A:

Q: i need the answer quickly

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.