Figure illustrates the connection of a cylinder head to a pressure vessel using 10 bolts and a confined-gasket seal. The effective sealing diameter is 150 mm. D = 20 mm (E = 207 GPa), and F = 25 mm (E = 100 GPa). The cylinder is used to store gas at a static pressure of 6 MPa. Bolts with a diameter of 12 mm, a = 30°, pitch of 1.75 mm, nut thickness H = 14 mm, At = 84.3 mm?, W = 18 mm have been selected. (a) Find the bolt spring rate kp (use E = 207 GPa). (b) Find the upper, central and lower frustrum stiffness per bolt (c) Find the member spring rate km

Figure illustrates the connection of a cylinder head to a pressure vessel using 10 bolts and a confined-gasket seal. The effective sealing diameter is 150 mm. D = 20 mm (E = 207 GPa), and F = 25 mm (E = 100 GPa). The cylinder is used to store gas at a static pressure of 6 MPa. Bolts with a diameter of 12 mm, a = 30°, pitch of 1.75 mm, nut thickness H = 14 mm, At = 84.3 mm?, W = 18 mm have been selected. (a) Find the bolt spring rate kp (use E = 207 GPa). (b) Find the upper, central and lower frustrum stiffness per bolt (c) Find the member spring rate km

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces shown acting on the pulley surfaces represent the belt tensions. The shaft is to be made of ASTM grade 25 cast iron using a design factor na = 2.8. What diameter should be used for the shaft? 6-in D. 300 lbf 27 lbf 360 lbf D 6 in A 8 in 50 lbf B 8-in D. 8 in
Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each are held together by means of a bolt. The bolt material S-400 N/mm² and E210000 N/mm² while plate material E= 72000 N/mm². The initial preload in the bold is 6.0 KN and force on the joint is 12 kN. Find out size of bolt assuming factor of safety 2.0.
Requlred Information A countershaft carrying two V-belt pulleys Is shown In the figure. Pulley A recelves power from a motor through a belt with the belt tensions shown. The power Is transmitted through the shaft and dellivered to the belt on pulley B. Assume the belt tenslon on the loose side at B Is 15 percent of the tension on the tight side. Glven B(dg) = 400 mm, TA = 575 N, and TỊA2) = 3835.25 N. 300 450 400 TIA T(A2Y `150 250 dia. B(da) 20 dia. B At the point of maximum bending moment, determine the bending stress and the torslonal shear stress. The bending stress at the point of maximum bending moment is [.09515 MPа. The torslonal shear stress at the point of maximum bending moment is 259.442 MPа.
Urgent
please i need her solving with using the formulas attached below of pin joint linkage
Required information A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at 8 is 15 percent of the tension on the tight side. Given: T41-550 lbf, T42=82.5 lbt, d4 = 6 in. dg=7.5 in, and dshaft = 1.292 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part TAI YAS A(DA) dshaft B(da) Determine the tensions in the belt on pulley 8, assuming the shaft is running at a constant speed The tension on the loose side of the belt ot Bis lbf. The tension on the tight side of the belt at Bis lbf.
A steel rod, which is free to move, has a length of 200 mm and diameter of 20 mm at a temperature of 15°C. If the rod is heated uniformly to 115°C, determine the length and the diameter of this rod to the nearest micron at the new temperature if the linear coefficient of thermal expansion of steel is 12.5 x 10 m/m/°C. Wrong solution will be reported instantly
The spring clamping force Fg = 2 N. The contact pressure force FA and the joint forces Fg at the jump piece 1 should be determined for the toggle mechanism with a straight guide shown in figure. C 26 mm B 2 10 mm A 1 8 mm 7 mm D 10 mm 15 10 ww ww
Urgent
The figure illustrates the connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure pg. For the specifications given in the table for the specific problem assigned, select a suitable bolt length from the preferred sizes in Table A–17, then determine the yielding factor of safety np, the load factor nL, and the joint separation factor n0. See problem number 8-36, and please use the FEA exponential curve-fit for member stiffness.
The spring of the check valve seen in the figure is mounted with a pre-stress of 12 mm and the diameter of the Spring Wire is 2.7 mm, the number of winding is 13, the slip module is 80800 N/mm?, the average diameter of the winding circle is 23 mm. If these conditions are taken into account, check the spring strength by finding out how much pressure the check valve will open at. Publication safe shear stress value is 185 N/mm? and 1 bar = 0.1 N / mm? will be taken. Ø10
A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.