Figure #4 shows the sending and receivinglend voltages v. and v, of a medium transmission line. V₂ 12 µF 10 52 wwwm 150 mH 12 μF Figure #4 a. Derive the transfer function H(s) 25 2 300 mH ww Load b. Hence or otherwise determine the poles and zeros of the circuit c. Determine the inductor and capacitor values for a "pi" (nt) configured constant-K, band-pass filter with cut-off frequencies of 18.4 and 18.8 MHz and surge impedance 2 kQ V,

Figure #4 shows the sending and receivinglend voltages v. and v, of a medium transmission line. V₂ 12 µF 10 52 wwwm 150 mH 12 μF Figure #4 a. Derive the transfer function H(s) 25 2 300 mH ww Load b. Hence or otherwise determine the poles and zeros of the circuit c. Determine the inductor and capacitor values for a "pi" (nt) configured constant-K, band-pass filter with cut-off frequencies of 18.4 and 18.8 MHz and surge impedance 2 kQ V,

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An unmodulated carrier is 680 Vp-p. Calculate the %m when its maximum p-p value reaches 650, 850 and 1050 V, and the minimum p-p value reaches 500, 300 and 50 V, respectively, upon modulation.
Inductance is not a transmission line parameter. Select one: O True O False
Logic
In general terms we can consider that the real propagation of electromagnetic waves is rectilinear. Select one: True Fake
1.2 When the modulation percentage is 75%, an AM transmitter radiates 10KW Power. How much of this is carrier Power? Solution: P, = 10 KW and m=0.75 %3D We know that
Q20. i) Choose the type of cable used to for short distance subscriber loop. Justify why this cable is preferred over coaxial cable. ii) Draw the structure and label the parts of coaxial cable. iii) The equation for AM signal is given by VAM (t) = 9 sin( 2n × 1550 × 10³t) + 3 cos( 2n × 1500 × 10³t) – 3 cos(2n × 1600 × 10 t) %3D Its radiated by an antenna with a resistance of 152. a) Find the total power carried by the given AM signal. b) Calculate the power in each side band.
Help me
A transmission line is 300 km long and the terminated to its characteristic impedance. the line has a resistance (R) of 10.4(OHm/km), a capacitance (C) of 0.00835 (uF/km) , an inductance (L) of 3.67 (mH/km) and a conductance (G) of 0.8 (uS/km) at frequency of 769 HZ.a) Find the attenuation constant ,the phase constant, and the characteristic impedance (ZO), b0 determine the voltage and currrent at the receiving end if a 2V generator with internal resistance of 60OOhm is connected to the sending end
The standing wave on a transmission line is caused by: Select one: a. The interference between V* and I . b. The interference between V 0. and I. c. The interference between V(2) and Vot. d. The interference between V(z) and I. e. The interference between V(2) and Vo. f. The interference between V(2) and I,. g. The interference between V and I5 .
For a Transmission line, draw the equivalent model & derive voltage and current expression. A transmission line has primary constant R= 0.1 ohm per meter,, G=0.02 mho per meter, L=0.01 micro Henry per meter and C= 100 pico Farad per meter. Find the characteristic impedance (Z0 ) at 5 GHz.
We want to send the message signal m(t) = 2 sin(20nt) - 8 cos(140nt) through an AM transmitter with a carrier signal c(t) = cos(2000nt). A) Find the frequency spectrum of the modulated signal and determine the bandwidth required to send the signal. B) Get the maximum possible modulation index (to achieve maximum power efficiency)
What is the resulting signal of the following Hartley SSB modulator? + sin 2πfct m(t). -π/2 a. The LSSB signal. O b. The inverted LSSB signal. c. The inverted USSB signal. O d. The USSB signal. + сos 2πfct