THEORY OF MACHINES Figure 1 shows a shaft that carries a flywheel and a gear, along with two smaller discs forbalancing Both the discs and flywheel have an imbalance. The system has the following initialposition data:mast = 4.54 kgRest = 82.9 mm @ 48.8°mgutei = 6.8 kgRouae = 76.2 mm @ 35°The distance between balancing plane 1 and 2 is 423 mm while the distance between balancingplane 2 to flywheel and balancing plane 1 to disk are both 108 mm.DiscFlywheelY Balancing plane 1Balancing plane 2Figure 1: Shaft system (Figure NOT in scale)(a) Sketch and label the statistically balanced link of the system.(b)Write the summation of force and moment equations of this system.(c) Calculate x- and y-component of each of the existing weights.(d) Determine the new changes for the radius in meter (m) and angles of the balancingweights needed to balance the system if balancing weight in Plane 1 weighs 25 N andin Plane 2 weighs 38 N.

Answered: Image /qna-images/answer/7e639c8f-09f4-43e3-80e8-f6e0d648c8e7.jpg

Figure 1 shows a shaft that carries a flywheel and a gear, along with two smaller discs for balancing. Both the discs and flywheel have an imbalance. The system has the following initial position data: mas = 4.54 kg Rask = 82.9 mm @ 48.8° Rouan = 76.2 mm @ 35° mouhe = 6.8 kg The distance between balancing plane 1 and 2 is 423 mm while the distance between balancing plane 2 to flywheel and balancing plane 1 to disk are both 108 mm.

Figure 1 shows a shaft that carries a flywheel and a gear, along with two smaller discs for balancing. Both the discs and flywheel have an imbalance. The system has the following initial position data: mas = 4.54 kg Rask = 82.9 mm @ 48.8° Rouan = 76.2 mm @ 35° mouhe = 6.8 kg The distance between balancing plane 1 and 2 is 423 mm while the distance between balancing plane 2 to flywheel and balancing plane 1 to disk are both 108 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

There is a 6 bar mechanism shown in the drawing. You are expected to operate this mechanism by turning the crank (limb I and I). Resize this pair (lim I and II) so that the round-trip time ratio is 1. t depth = 1 treturn
The figure below shows the four-bar mechanism given with ABCD. Of 2000 N force In order to have a static balance when applied; (by graphic method) a) Find all the forces affecting the limbs. b) Find the magnitude and direction of torque T.
In the following system the wheel rolls without sliding. The number N of degrees of free dome of the system is k. k k k F(t) m m N=5 N=2 N=6 N=3 Clear my choice
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A 4 bar crank -rocker mechanism has the following configuration link 1=d=152.4mm „link 2=a=50.8mm „link 3-b=177.8mm and link 4 =c=228.6mm and if 02 input variable 30° .find out possible open and cross value of 03 and 04. (Hint: setting scale 20mm =1 cm)
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
theta O = 55 The link length and value of O2 for some four bar linkage are defined below, (drive link =4.2 cm , coupler link =5.9 cm , follower link = 5.9 cm, fixed link= 6.85 cm 1. draw the linkage to scale and graphically find all possible solution (both open and cross) for 03 and O4 2. If w = 2 rad /s (CCW) find the angular velocity for bar 3 and 4 3.if a= 5 rad/s? (Ccw) find the normal and tangential acceleration for link 3 and 4
Pls help me with my plates Block 4 slides in the slot in the fixed piece 1. Axis Q2 of crank 2 is fixed on 1. Q2A = 1.5 inches, and AB = 4.5 inches. Draw the mechanism, assuming dimensions for 1, if desired or use center lines only. Draw the four-bar linkage for this mechanism, properly rotate the linkage Q2ABQ4∞, name each link, and show the finite infinite cranks.
2) Block 4 slides in a slot in the fixed piece 1. Axis Q₂ of crank 2 is fixed on 1. Q₂₂A = 1 1/2 in., and AB = 4/1/2 Draw the mechanism, assuming limen- sions for 1, if desired, or use center lines only. Draw the four-bar linkage for this mechanism, properly rotate the linkage Q₂ ABQ400; Name each link, and show the finite and infinite cranks. Frind graphically the two extreme positions of 13, The axis of the pin by which link 3 is attached to the block 4.. Dimension the length of the stroke of B. Ans. 3& in. for scale 1:1
Identify whether the following set of dimensions determines a Grashoff, Non-Grashoff or SpecialCase mechanism. If it is a Grashoff mechanism state what is kind of kinematic inversion it is
Problems 10-16 Information: Jose' pushes a wheelbarrow consisting of a wheel (mass mw = 3 kg, radius r= 0.1 m) and a barrow body (mass mg = 30 kg). He accelerates from rest (state 1) to a velocity of 2 m/s (state 2), when he trips and lets the wheelchair roll down the hill (height h = 2 m, 30 deg angle) to the bottom (state 3), where it hits a crate (mass mc= 20 kg) into motion (state 4). The ground has a friction coefficient of 0.5. Between states 1 and 2, when Jose' is balancing the wheelbarrow, all the weight is on the wheel. After that, the support spike drags along the ground, holding half the total weight, while the other half is on the wheel. 13). Draw the FBD and write the equations of motion for the wheelbarrow descending the hill. What is its acceleration? (keep in mind there are 2 normal forces) 14. What is the speed at the bottom of the hill? 15. If the collision between the wheelbarrow and the crate has a coefficient of restitution e = 0.6, how fast does the crate move…
A four-part mechanism like this one, if it is known the length of O2A (link 2) is 5 cm (link 3) is 4 cm (link 3) and the length of the bo4 (link 4) is 5.5 cm (5 in.). At the a point working the p = 50 Newton style with the sustric orientation of the horizontal line is 200 look for styles that are going on and torque on link 4.