Figure 1 shown below has pinned supports at A and C, and B is a fixed joint. Assume El is constant throughout and: i) Determine the shear and moment of end B of the cantilever member BD ii) Determine the moments at B, A, and C using slope deflection fixed. hinged connection equations iii) Sketch the moment diagram for the frame (FEM diagrams given on back data sheet) 50 kN/m 4 m B 100 kN El=constant 2m timt 4m

Figure 1 shown below has pinned supports at A and C, and B is a fixed joint. Assume El is constant throughout and: i) Determine the shear and moment of end B of the cantilever member BD ii) Determine the moments at B, A, and C using slope deflection fixed. hinged connection equations iii) Sketch the moment diagram for the frame (FEM diagrams given on back data sheet) 50 kN/m 4 m B 100 kN El=constant 2m timt 4m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4-2 kN, a= 2 m and h=2 m, you are required to: h P1 P2 P3 P4 D P1 E d) Using the method of sections, determine forces on members GF, GC, CD. 7 e) Using the method of sections, determine forces on members GH, BG, BC. Note: You are required to draw the FBD and apply the equilibrium equations for each case.
Use 2 decimal places.
Determine the shear value when x = 6m (from the left) for the beam shown Where: P1 = 51kN; P2 = 42 kN; W1 = 11kN/m; W2 = 21kN/m 4m P1 P2 w2 44/2 m² 4 R R₁ 2 m A EU 5 m W1 3 m
1. From the truss loaded as shown, determine the stress induced on each of the members BC, BD and CD. Consider each member has a cross sectional area of 1200 sq. millimeters. Consider the pulley to be frictionless. Solve the required forces using method of joint and method of sections. 110 kN 5 kN 10 kN 2m 4m 2m E 3m 2m 20KN
.The beam is subjected to the loads q0 and P, with the values added to the table below. Point C, where force P is applied, is located at L/2 from points A and B. Knowing, that cross section of the beam has moment on inertia equal to 232*106 mm4 .The beam was modified to improve its performance and structural integrity roller support was placed at point B. For the system determine: a) Plot shear force and bending moment diagrams and find the most loaded cross section
Use the virtual work method to determine the vertical displacement at joint I. (The area for all truss members = 800 mm², and E = 200 GPa). Show detailed calculations of the analysis of the truss under the real and virtual loads (combine both method of joints and method of sections). B J 20 KN 20 KN H 20 kN 5 @ 5m= 25 m E 20 kN 10 kN- 5m
Please answer with the complete solution
Determine the force in Member EG of the truss shown when P = 20 kips. F D H O O B 7.5 ft A 0000 K 13.00 kips. Tension O 14.00 kips. Tension O 15.00 kips, Tension O 16.00 kips, Tension C E G I P P 6 panels @ 6 ft = 36 ft
A. All the member forces using the Method of Joints B. Axial force at member BE using the Method of Sections Dimensions: AC-CE-EF-1 meter BC-DE-0.8 meter Draw the shear and moment diagram of each truss members. 400 KN B C a 400k Lu E 500 KN
Please help to solve the problem below. need to determine the shear force acting at each of the following locations. Will surely give a like to the answer. Thank you Sir/Maam.
Upvote will be give. Please write the complete solutions and draw FBD. Use 2 decimal places. Determine and Draw also the shear and bending force and FBD.