Fig.10 shows an off-set piston mechanism in which the crank OA rotates clockwise at 2500rpm. Determine: The velocity of the piston B The acceleration of piston B The angular acceleration of the connecting rod, AB A

Q: 2. A four-stroke reciprocating engine have a 2000 indicated horsepower. What would be the indicated…

A:

Q: i cant read this.. can you write it out??

A:

Q: さutてosuう +1 U、ズX ) Given. find dd.? dx

A:

Q: Please look at pic. Please help, I don't get part b. Thanks

A:

Q: i cant read this, can you rewrite

A:

Q: Can you please write them down cause im struggling to understand when you are typing

A: The given information in the problem is shown in the following attached image:

Q: The hand writing is not very clear :(

A: Basically the miller indices are the set of numbers which define the particular plane in the crystal…

Q: EX7: write a program read any vector and print the odd order only?

A: Required: Program to read vector and print item ad odd order.   all the code with code screenshot…

Q: .She was half . hour late The O A An O No thing O هذا السؤال مطلوب Nadia always hard before…

A: Correct answer: an Reason: We know that, the preposition 'an' comes before a, e, i, o, u words. At…

Q: Illustrate the correct sequence of the Theory of Accidents by Heinrich? A. B. C. D. Social…

A: Heinrich's Domino Theory states that accidents result from a chain of sequential events,…

Q: determine Vp, f, and Ø, and insert

A:

Q: Match the letter to the correct part description based on the picture of the milling machine below.

A: Milling Machine Parts name

Q: A power plant turbine releases its discharge into a condenser operating at 20C at 100% saturated…

A: It is given that:condenser temperature is 20°C. Steam enters condenser as 100% saturated vapor.Mass…

Q: b)Calculate Degree of freedom for the following figure. Activate Windows Go to Settings to activate…

A:

Q: i. The venturi meter has water flowing through it and the liquid used in the manometer (as shown in…

A:

Q: Find the work W done by a force of 3 pounds acting in the direction 45° to the horizontal in moving…

A:

Q: EX6:write a program read any vector and print the odd number only?

A: Note: Here you didn't mention any programming language so we are creating the program in the C++…

Q: Known values: L Rp Wdisk a disk 0.9 m 0.4 m 33° 30° 10 rad/s 10 rad/s? .2 Problem Statement: A disk…

A: Peg attachment mechanism:- In the case of spinal disc replacement options, we can conduct many…

Q: Thank you for this answer. I don't quite understand step 4, 5 and 6 because the operation is not…

A: given; all values given

Q: Write the function of ortho on in an AutoCAD system. When and why we use this command during…

A: Ortho System In AutoCAD, the Ortho mode is used to limit the movement of cursors to certain…

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: I don't understand due to the way its written, can it be written again but more clearly pls

A: From the question, the given data are: Volume of heater = Capacity of heater =V1 =  2 liters = 2 x…

Q: Yousef family will be visiting the governorate of Amman in the Hashemite Kingdom of Jordan in the…

A: The given question can be condensed to a more precise sentence. The hashemite kingdom of Jordan can…

Q: Hot water (specific heat of 4.18 Kj/kgK) at 66C is flowing through a metal pipe (6 m long, 2 cm ID,…

A: Given  Hot water is flowing through a metal pipe.  Specific heat of water = 4.18 Kj/KgK Temperature…

Q: b) Calculate the inclined angle λ and orthogonal rake angle yo, when yx =10°, yy =8°, ps=15°.

A:

Q: 10) Define the slip angle.

A: The angle between the direction of the wheel in which it is pointing and the direction in which it…

Q: A centroid is an object's geometric center. For an object of uniform composition, its centroid is…

A: Hi, As per the guideline, we can not provide you with a handwritten solution.

Q: 01: Write G code to Write the first Letter of you name

A:

Q: Homework: Apply Gruebler's Equation to determine DOF. mesen

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.