Fifth question: A motor up to three-phase, the number of poles is 4, and it operates at a frequency of 50 Hz, the slip factor at full load is 5%. Single phase resistance and reactance 1.05 and 4.2 ohms, respectively, and at rest. If the voltage on the slip rings is 90 volts at idle. Calculate the current through the rotor winding and the power factor. Jo 10:11

Fifth question: A motor up to three-phase, the number of poles is 4, and it operates at a frequency of 50 Hz, the slip factor at full load is 5%. Single phase resistance and reactance 1.05 and 4.2 ohms, respectively, and at rest. If the voltage on the slip rings is 90 volts at idle. Calculate the current through the rotor winding and the power factor. Jo 10:11

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In general, which of the following is/are a factor that will determine the synchronous speed of a 3-phase motor? 4. a) frequency b) number of stator poles per phase c) both "a" and "b" d) neither "a" nor "b"
DC/AC MOTOR (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATIONS NEEDED. ANSWER IN 2 DECIMAL PLACES. BOX THE FINAL ANSWER.)
Question -9b
QI: The parameters of a 4 kW, 220V. 2-phase induction motor, in ohms per phase, are: r1=0.53, x1 =2.4, XM= 70, r2 = 0.96, x2 = 3.0. The motor is operated from unbalanced 2- phase source whose voltages are 230V and 210V, the smaller voltage is lagging the larger by 800. For a slip of 5% and rotational losses of 30 W, find the positive- and negative- sequence components of: (a) the applied voltages. (b) Find the values of phase currents (c) the input current. (d) Find the developed mechanical power. (e) Find the efficiency.
A three-phase slip ring induction motor develops full load torque at a slip of 0.04 when the slip rings are short circuited. If the rotor resistance is increased 3 times by inserting external resistance in the rotor circuit, then the slip will be:
2) A large 3-phase, 4000 Va (phase to phase), 60 Hz squirrel-cage induction motor draws a current of 385 A/phase. The total active power at the stator input terminals is 2344 kW, when operating at full load. The corresponding speed is accurately measured and found to be 709.2 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.10 Q. The total iron losses are 23.4 kW and the windage and friction losses are 12 kW. Calculate the following: c) The total 1²-R losses in the rotor d) The load mechanical power (kW), torque (kN•m), and efficiency. S = Va · V3 - I S= Vy•3·I %3D
Q2. a) A 415V, 50Hz, 3-phase induction motor supplies its rated power to a load. The rated speed of the motor is 980 rpm. b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (i) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.
A three phase induction motor is wound for 4 poles and is supplied from 50Hz system. Calculate the synchronous speed and speed of the motor when slip is 4.1%