F4-40 Determine the resultant force and specify where it acts on the beam measured from A. 200 lb/ft 500 lb 150 lb/ft A B -6 ft- -3 ft - -3 ft-

Q: l force onto the inner bottom rim of the lid. Given that the Dol at point A and a 20-lb force is…

A: The force exerted on the handle is .To find-The force exerted on the rim.

Q: Replace the loading by a single resultant force, specify the location of force measured from point…

A: Note that, the center of mass of a uniformly varying loading (UVL) acts at the position of two-third…

Q: The square gate AB is held in the position shown by hinges along its top edge A and by a shear pin…

A: d=4.5 ftArea of gate=1.8*1.8density of water,

Q: Replace the loading on the frame by a single resultant force. Suppose that Fi = 250 lb , F2 = 90 lb…

A: Given data as per question F1 =250 lb F2 = 90 lb M =500 lb. ft considering horizontal forces  as…

Q: P1-1. Draw a free-body diagram of the ring at A and identify each force. 30° 200 N 500 N (c)

A: To draw: The free body diagram at ring A and identify each forces. FBD: The free body diagram at A.…

Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 800…

A:

Q: The force Ris the resultant of Pand Q. Determine Q and the angle e. P = 3 kN R= 2 kN

A:

Q: Determine the location of the resultant force measured from point A

A:

Q: If you replace the three forces acting on the shaft by a single resultant force (798 lb) with an…

A:

Q: Replace the loading system by an equivalent resultant force and specify where the resultant's line…

A:

Q: 200 - 400 A 200 N m D E 200 F Dimensions in mm Determine the magnitude of the force (in N) of the y-…

A:

Q: Q- 6- Resolve the force 250N into rectangular components 250 N 16 9. 12

A: Here, Magnitude of the force = 250 N   For the given triangle, missing angle θ can be found by,…

Q: -5 ft 3 ft- 2 ft 4 ft B В 5 3 12 13 4 5 500 lb 200 lb 260 lb

A:

Q: 5. The 1800-N force F is applied to the end of the I-beam. Express Fas a vector using the unit…

A:

Q: Use the method of sections to find the true magnitude and direction of the force in member AB of the…

A:

Q: F- 10N 250 mm The 10-N force is applied to the handle of the hy- draulic control valve as shown.…

A: Solution: The Joint at B will have a Force F=10N and a moment due to this force will be acting on…

Q: Determine the components of the 300-lb force directed down to the right at a slope of 2 (opposite)…

A: Given data: F=300 lb Need to determine the components of the force.

Q: 600 lb-ft B 350 lb-ft 3ft 1 ft 500 lb-ft 2 ft

A: For solution refer below images.

Q: Determine the forces marked with "x" by using method of section 50 kN 30 kN- 3 m G 30 kN– 3 m

A: Take a section X-X, and cut the truss through IH, FG and FC. And, consider the upper part where,…

Q: Determine the angle a detween forces F, and F2. 2 m -3 m 3m - 50 kN I m F =30 kN y

A: The given system of forces is – Writing the coordinates of the system of the forces,

Q: (write your answer as this example: FR = ??, a = ??, g = ??). Note: FR is resultant force, a is…

A: GivenF1=429kNF2=359kNF3=240kNα=61oγ=74o

Q: Q3/ Replace the force system with a single force and determine its exact location. 3m 500 N 2 m 500…

A:

Q: Determine the angle between the two ropes. 1 m 2 m 1'm 3 m B. -y •G 1 m 1m

A:

Q: Q.1) Find Qand the angle 0. If the force Ris the resultant P=3 kN of Pand Q. 55° R=2 kN

A: Given: P = 3 kN R= 2 kN   To find: Q= ? theta = ?

Q: 3) Determine the resultant force and specify where it acts on the beam measured from A.

A: Given:Find:the resultant force and its location from point A.

Q: 3- Determine the force T and C 3 kN 20 16 kN 40 8 kN

A: In horizontal direction    Tcos40+8+Csin20-16=00.766T+0.342C=8         -1

Q: 2/52 Determine the angle e which will maximize the moment Mo of the 50-lb force about the shaft axis…

A:

Q: Replace the load acting on the beam with an equivalent resultant force. Specify the location at…

A: To get the equivalent resultant force we will just apply the equilibrium conditions for given…

Q: 06. The resultant R of the concurrent forces F, T, and Q acting on the screw eye has the magnitude…

A: The resultant R of the concurrent forces F, T, and Q acting on the screw eye has the magnitude and…

Q: Given a system made of the force F, couple M and distributed loads defined by w1 and w2, find the…

A: To find :  The equivalent system at B  Given :  The Force is F=8 kN The moment is M=5 kN·m The…

Q: In the equilibrium position shown, the resultant of the three forces acting on the bell crank passes…

A: To solve this problem, we need to first resolve the force P in horizontal and vertical direction.…

Q: Replace the loading by an equivalent resultant force and specify its location measured from A.

A:

Q: 2 KN/m 2 KN/m URN A 30 3.0m 3m 2.0m 2.0 m 4,0 m

A: There are three different types of loads are there on this beam which are Uniformly varying,…

Q: 1. Determine the magnitude and direction with respect to the +x axis on the reaction at A and at C.…

A: