(F3 = 800 lb F2= 600 lb 30% F, = 700 Ib Probs. 2–81/82/83

Q: For the sections presented below determine the position of the centroid axis and the moments of…

A:

Q: A wide flange section has the following properties: bf = 250 mm tf = 10 mm d = 300 mm tw = 7 mm…

A:

Q: 3. Compute the reacting forces RA and Rg at the ends of the beam shown. These reacting forces are…

A: Given simply supported beam with inclined point load 130 N. It is asked to calculate support…

Q: Determine the moment of inertia of the shaded region around the ?−x− axis. ??= ____mm4   Part b)…

A:

Q: Analyze all member forces by using method of joints

A:

Q: 1. Det.moment of inertia. Y 3" r= 3" 4" 1" 2"

A:

Q: 632 lb 3" 1000 lb 722 lb 2" Figure P9 12 13

A: To find resultant and direction

Q: Based on the the truss given, what is the value of force acting on member AD? * CO00 KN 24D KJ 0 Ham…

A:

Q: What is the purpose of shear and moment diagram

A:

Q: For Probs. 18.1 to 18.6, using the virtual-work method, determine the deflection of each of the…

A: A truss is given we need to find out the vertical and horizontal deflection of U2.*Note: As per…

Q: kip-ft /EI. The maximum deflection is mostly near O A. 2389 O B. 3755 OC. 10500 O D.7833

A: To find maximum deflection

Q: Determine the Y-Component (My) of the couple acting on the frame below at point O due to the shown…

A: Data Given: a = 0.7 m F = 532 N Asked: Y component of the moment acting on the frame

Q: Problem 3: A. The rigid pole and cross-arm assembly is supported by the three cables shown. A…

A: Feel free to ask any doubt.

Q: 3

A:

Q: find the horizontal force at support "A" by force deflection method

A:

Q: P₁=25kN C A P₂=75kN 2.0m D 1.5m 1.5m E 1 F P3=45kN B TITTTTTT 2.0m Support at B is a pin 1.5m 1.5m

A:

Q: Determine the rotation and deflection under load in the beam with the following external moment…

A: ind reactions:∑ MA=0RB5-20=0RB=4Kn∑ Fy=0R+RB=0RA=-4KnSO moment equation:Mx=-4x+20x-20

Q: 4:25 ||| 80 mm ا.. اس = 319 .. 3. If the bolt head and the supporting bracket are made of the same…

A: Given data,  Failure shear stress for both bolt head and supporting bracket is = τ = 120 MPa = 120…

Q: Determine the magnitude and coordinate directionangles of the resultant force of the two forces…

A:

Q: This problem is about replacing the loading system acting on the beam shown below by a resultant…

A: Objective: To replace the given force system with a resultant force and couple moment acting at…

Q: Find the horizontal defleftion of joint E. E= 2,000 ksi; I= 10,000 in⁴

A:

Q: Determine the force-couple system acting at point 0. 50 N 90 N 40° В 40 N m 400 mm 1300 mm A 4 800…

A:

Q: Locate the centroid y̅ of the cross section and determine the moment of inertia of the section about…

A: The given figure can be divided into three parts as shown below.

Q: Determine the distance H from the upper surface of the symmetric double-T beam cross section to the…

A:

Q: Three

A:

Q: 60N LO 30 Nm, CCW 30 Nm, CW 270 Nm, CCW 270 Nm, CW L C. -10 1. Which of the following gives the…

A:

Q: Part A Determine the magnitude of the projected parallel component of the force F to pipe segment…

A: Given : Determine the magnitude of projected parallel component of force F to pipe segment AB ?

Q: Help me answer the photo attached please.

A:

Q: If F1 = 100 N, F2 = 120 N, and F3 = 80 N, determine the magnitude and coordinate direction angles of…

A: The given force vectors are,

Q: Calculate the moments of inertia of the built-up steel mer ber shown with respect to both centroidal…

A: Given:- Channel:- C12 X 20.7 Wide flange :-W10 X 45 To find:- Moment of inertia

Q: A.) CREATE A SHEAR DIAGRAM BY AREA MOMENT AND BY PARTS 3.) CREATE A M/EI DIAGRAM BY AREA MOMENT AND…

A:

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.