F15–12. The cannon and support without a projectilehave a mass of 250 kg. If a 20-kg projectile is fired from thecannon with a velocity of 400 m/s, measured relative to thecannon, determine the speed of the projectile as it leavesthe barrel of the cannon. Neglect rolling resistance.30

Answered: F15–12. The cannon and support without…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A motorcycle and rider have a combined mass of 350kg. The vehicle's velocity is 100 km/hr. The rider is to go up a hill incline of 10 meters. The wheels each have a mass of 20 kg and a diameter of 500mm. The wheel design consists of 6 spokes with a mass of 0.5 kg for each spoke. a. Determine the vehicle's velocity at the top of the hill, assuming it was a rolling vehicle with engine being turned off. a. Indicate the vehicle's velocity at each meter through the climb. b. Explain the transfer energy and how this affects the behaviour of the system. At another point in its journey, the motorcycle and rider travel at 80 km/h around a left-hand bend of radius 30m. Calculate: a) The angular velocity of each wheel. b) The moment of inertia of each wheel. c) The angular momentum of the wheel prior to entering the bend. d) The magnitude of the gyroscopic torque produced on the bike as the rider is driving around the bend. What is the effect and why is it important to calculate the gyroscopic…
Q110
The 4-kg collar C has a velocity of ?? = 2?/? when it is at A. If the guide rod is smooth, draw a free body diagram and determine the speed of the collar when it is at B. The spring has an unstretched length of ?o =0.2?
F13–11. If the 10-kg ball has a velocity of 3 m/s when it is at the position A, along the vertical path, determine the tension in the cord and the increase in the speed of the ball at this position. 2 m e = 45° A3 m/s
Box A is traveling down the smooth incline (0= 17°) and it hits box B, initially at rest, with the velocity of 5 m. Immediately after impact, box A moves up the incline with the velocity of 1 m. Determine the velocity of box B (in m) immediately after impact. Consider ma = 3 kg and mB = 18 kg. The positive direction is shown on the figure. VA В
PLEASE ANSWER NUMBER 3.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
The 1900-kg car has a velocity of 21 km/h up the 10-percent grade when the driver applies more power for 13 s to bring the car up to a speed of 64 km/h. Calculate the time average F of the total force tangent to the road exerted on the tires during the 13 s. Treat the car as a particle and neglect air resistance. 10 100 Answer: F = i kN
The 1440-kg car has a velocity of 26 km/h up the 7-percent grade when the driver applies more power for 10 s to bring the car up to a speed of 64 km/h. Calculate the time average F of the total force tangent to the road exerted on the tires during the 10 s. Treat the car as a particle and neglect air resistance. 1 7 100 Answer: F = kN
Conservation of Linear Momentum A 0.6-kg brick is thrown into a 25-kg wagon which is initially at rest. If, upon entering, the brick has a velocity of 10 m/s as shown, determine the final velocity of the wagon
A gun shoots an 8.0 g bullet into the 2.0 kg wooden block of ballistic pendulum. The block and bullet then rise to a height of 65 mm. Determine the velocity of the bullet fired by the gun.
The 1.5 Mg car increases its speed uniformly from rest to 36 m/s in 8 s up the inclined road. Determine the maximum power that must be supplied by the engine, which operates with an efficiency of ε = 0.42. Also, find the average power supplied by the engine. Please show every single step of the process thanks
Determine the constant force “f” w/c must be applied to the cord in order to cause the 39lb block to have a speed of 22 ft/a when it has been displaced 0.5 ft upward starting from the rest.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

F15–12. The cannon and support without a projectile have a mass of 250 kg. If a 20-kg projectile is fired from the cannon with a velocity of 400 m/s, measured relative to the cannon, determine the speed of the projectile as it leaves the barrel of the cannon. Neglect rolling resistance. 30