F1=200# Problem # 3 25" The bent pipe resists forces as shown. Determine the moment of each force about each of the coordinate axes (9 results required). В 40" F2=500# 12" F3=400# A

Q: 1.3 Determine the length of side a and the measure of the two acute angles. 72.0' 67.3'

A: find the side a and two acute angles.

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

A:

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: What are the two dimensions that are not placed on the field of a drawing? A zero and a 45 degree…

A: The following things needs to be mentioned on the field of drawing: ◆ The diameter or radius of…

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: 2 Constraint indicated the name and where it should be

A: Given: To find: Where the constraint should be

Q: Question The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall…

A:

Q: Draw the front, Side and top

A: We need to draw three orthographic projection views.

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: 3. It is desired to design a 5-cylinder aircraft engine with a stroke-bore ratio of 1.2. The piston…

A: here, stroke bore ratio say, l/d ratio = 1.2 so, l = 1.2×d volume per cylinder = π4·d2·l here,…

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Draw chalk diagram of all sections

A: To draw section views

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: Determine smaller diameter, All dimensions are in mm) 110.916 091 S 100.916 80.916 mm cant be…

A: The smaller diameter is 80.916 mm.

Q: Express the results of the following multiplications and divisions to the proper number of…

A:

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: 2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits…

A:

Q: Round number to three significant figures. 1.548937 x 10^7

A: For scientific notations significant digits/figures are calculated only for the coefficient or…

Q: 1. How is fraction changed to decimal? A. Divide the denominator by the numerator B. Divide the…

A: Since we answer only one question at a time, we will answer the first one. Please resubmit the…

Q: LO 10 $ 25 R 3 R6 R 12 30

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: A midsized Dozer weighs 41,000 pounds and has 175 hp. If the machine is working at 80% efficiency…

A: Given Data The weight of the machine is: W=41000 lb The power is: P=175 hp The efficiency of the…

Q: For the laser cutting of the shown path, determine the absolute and incremental coordinates of the…

A: given; findabsolute and incremental co-ordinate;

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.