F

Q: A twin engine jet aircraft is climbing at a 30 degree angle at 260 ft/s. The thrust developed by a…

A: To Find : The power developed by the aircraft.Given :The velocity is .The thrust is

Q: QUESTION 1 1.1 The inverted U-tube manometer is used to measure the difference in pressure between…

A: The densities of the respective fluids are,Draw the schematic diagram for the given system.

Q: The gage pressure of the air in the tank shown below is measured to be 50 kPa. Determine the…

A:

Q: 1. Add the couple C = 40i - 30j + 50K N.m to the resultant vector of the three couples 20 N.m, -30…

A:

Q: A company has 237 employees. Of these, 205 participate in at least one of the company's two payroll…

A:

Q: Q. 60. The figure shows a schematic layout of a hydraulic jack. The load to be raised weighs 20,000…

A:

Q: A 2 kg mass swings in the horizontal plane in a circle with a radius of 1.5m and is held by a taut…

A:

Q: can you do a position analysis to this mechanism whether in geometric or analythical way to be able…

A: Given:

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3550 mm² and an…

A: Given data :- Area A1 = 3550 mm2   ;     Allowable normal stress =175 MPaArea A2 = 2050 mm2  ;…

Q: 6. A sheet of aluminum alloy is cold-rolled 30 percent to a thickness of 0.080 in. If the sheet is…

A: According to the given dataX1=0.080 inX2=0.064 inFirst cold rolled is 30%We need to findTotal cold…

Q: (centre to centre of bearing surface). Owing to the combined weight of armature and magnetic pull…

A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…

Q: Most of the CTDS representing Engineering products are: O 3-levels. O 2-levels. O 4-levels. O…

A: Solution:

Q: Task 2.2 A large pressure vessel contains air in state 1 (pi = 3 bar, T1 = 360 K, c1 = 0 m/s). The…

A: Given: At state 1p1=3 barT1=360 Kc1=0 m/sηsD=0.9State 2:p2=1 barA2=0.1 m2

Q: From the diameter of the sun and the earth and the mean distance of sun from earth, estimate (a) the…

A: Diameter of the sun = 1,392,000 km = 1.39 × 109m Diaplanet-Y= 340,800 km = 3.408 × 108m Mean…

Q: Model the Organization Structures and its Types

A: There are main 7 types of Organizational Structures...

Q: 9-76: Air is used as the working fluid in a simple Brayton cycle that has a pressure ratio of 12, a…

A:

Q: This walkway exerts equal vertical loads on this Warren truss at B, D, F, and H. Use the method of…

A:

Q: sketch the development

A: the given is isometric view

Q: Water (density 1000 kg/m) flows through an inclined pipe of uniform diameter. The velocity. pressure…

A:

Q: For the screw clamp shown, a force is applied at the end of the handle 3 in from the screw…

A: Given Data:- L=3.5 in T= 3.5 F

Q: Explain Design Procedure.

A: Design procedure is very basic thing to obtain some useful output with optimum conditions. We design…

Q: A machine member part is subjected to fluctuating stress of σ = ax cos(8nt) The endurance limit of…

A: Given:Fluctuating stress, σ=σo cos8πtendurance limit=350 MPAFOS=3.5Find,maximum value of  σo

Q: O. The vapor compression cycle 1-2-3-4-1 operates at evaporating temperature of 270K and condensing…

A:

Q: 98) Select fmax for analysis of a fan operating at 1175 rpm and supported by rolling element bearing…

A: Given : Rpm = 1175 rpm Number of balls, Nb = 12 Blades = 8 To find : Max frequency

Q: A pressure versus volume (pV) diagram for a system is shown in the figure. The arrows of the curve…

A:

Q: Different companies   use product mix price strategies when they are expanding the product line.…

A: Product mix is a type of portfolio of products that refers to the complete set of services and…

Q: Resolve the force F2 into components acting along the u and v axes and determine the magnitude of…

A: According to the given dataF2=420 NWe need to resolve the Force F2 Along the u and V axes

Q: A certain hospital has 415 patients; 76 have high blood pressure only, 123 have heart problems only,…

A:

Q: On a roulette wheel there are 38 sectors. Of these sectors, 18 are red, 18 are black , and 2 are…

A: Given Data N(R)= 18 N(B)=18 N(G)=2

Q: Determine the tension in cable BC and BA necessary to Support the 60 kg cylinder shown in the…

A: Given:mass of the cylinder, m=60 kg

Q: Draw the sectional view.

A: According the given view we need to draw the isometric view. i am using solid works to draw…

Q: S3) Investigate the following squared-and-ground-ended helical compression spring to see if they are…

A: Given: Material: A228 Music wire, Wire diameter, d=2 mm, Outer diameter (OD), do=10 mm, Free…

Q: Determine the moment of inertia of the composite area about the x- and y-axes. 6 in.- 3 in. 3 in. j2…

A:

Q: A solid round bar shown in figure (1) below with diameter of D=2 in has a groove cut to a diameter…

A: For hot-rolled steel AISI 1050, the ultimate strength and yield strengths are 120 kpsi and 66 kpsi…

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.