F. Hy

Q: A transmission tower is loaded as shown in the figure JCZ-1. Assume roller support at A and hinge…

A: Determine the stresses at member CE and DF.

Q: 400 N y 250 N B 60° Answers: 530 N 60⁰ 30° 590 N 410 N 30° G -17.5 m E 30 220 N

A:

Q: A vertical masonry chimney has a internal diameter d, and an external diameter d,. The base of the…

A: A chimney is a masonry, clay, or metal architectural ventilation structure that separates hot…

Q: A cantilever beam under a state of loading is shown below, determine the horizontal reaction at G?…

A: Consider the figure,

Q: The hydrostatic force due to linseed oil F1. b. The hydrostatic force due to castor oil F2. c.…

A:

Q: Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force (P) is…

A: Given C=2m J=4m E=1.2m Theta=60° S.G=0.82

Q: A homogeneous rectangular gate AB 7.9 ft wide and 10 ft long. Friction in the hinge is negligible.…

A: ρ=1000 kg/m3g=9.81 m/s2L=8.12 ft=2.475 mW=7.9 ft=2.408 mh¯=L2sin600=1.0717 m

Q: Qg: If the weightless half- cylindrical gate, show in figure below, is in equilibrium, what is the…

A:

Q: Q4) Determine the maximum shear stress acting in the fiberglass beam at the section where the…

A:

Q: Question Bank - Friction The two homogeneous bars AB and BC are connected with a pin at B and placed…

A:

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: beam loaded as shown. (a)What is the Value of horizontal reaction at the fixed support? (b)What is…

A:

Q: • Given the beam as shown: 50 kN Determine: 20 kNm a.) Reaction at A. A B D b.) Reaction at B. 3 m…

A:

Q: A homogeneous rectangular gate AB 5.5 ft wide and 10 ft long. Friction in the hinge is negligible.…

A:

Q: Q2. Replace the loading acting on the beam with a single resultant force. Determine (a) the force…

A: Replace the loading acting on the beam with a single resultant force. Determine (a) the force…

Q: A homogeneous rectangular gate AB 7.9 ft wide and 10 ft long. Friction in the hinge is negligible.…

A: Find force acted on surface AB

Q: Determine the minimum coefficient of static friction between the uniform 50-kg spool and the wall so…

A: Consider the free diagram of the spool shown below. Consider the moment about point A. Consider…

Q: H.W 4 Determine the equivalent resultant force of the system and specify its location measured from…

A: To find resultant and it's location from A

Q: The pipe assembly is subjected to the force of F = {600i + 800j - 500k} N. Determine the moment of…

A: The given data is shown below:

Q: 4. The gate shown is hinged at O contains water on one side and oil on the other. What force F is…

A: net horizontal force is zeroγ= 10 KNm3hw=force due to waterhoil=force due to oilhw*= cetre of force…

Q: 2. The pipe assembly is subjected to the force of F = (600i + 800j – 300k) N. Determine the %3D…

A:

Q: A. Determine the stress at the bottom in the free end. (MPa) 3. Determine the stress at the top in…

A: consider 15 % loss in prestress force

Q: 2 ft В seawater (SG = 1.03) 10 ft P 45° A

A: Weight of gate, W =600lbWidth of gate, B =20ftConsider unit depth of gate .Angle of gate with…

Q: A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.500 in. and a wall thickness…

A: Formula used for elongation or contraction δ=PLAEP=Load appliedL=Length of barA=Area of barE=modulus…

Q: 0.3m B Water 0.4m Oil RD=0.8 0.2m 0.4m Water 0.4m

A: Note :- as diagram can be read from the question itself so not drawing in answer as no changes is…

Q: Calculate the shear stress in MPa at section B A 100 mm F=10EN 10 mm

A: Shear stress:- shear stress is defined as shear force per unit area.

Q: ▼ Part A Determine the axial forces in members BD, BE, and BG. (Figure 1) Enter your answers…

A:

Q: Q4- A rectangular gate 6 ft tall and 5 ft wide in the side of an open tank is held in place by the…

A: height of gate=6ft width of gate=5ft

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.