f W=3.000 inches, Y=1.750 inches, and Z=0.875 inch, find X. E TE X A A W 1 B + B -Z- - с

Q: Given the equation of the circle x + y? - 2x - 4y+1 = 0, find the centre of this circle. A. (-1,2)…

A: Given Data- The equation of the circle isx2+y2-2x-4y+1=0.

Q: find controid of the area

A:

Q: Determine the location of the single resultant force due to the distributed load measured from A.…

A:

Q: 450 N 30 200 N m 0.2 ml 1.5 m 2 m 1.5 m 200 N Find the angle of the resultant to force O 30.14° O…

A: FBD of the given condition (with components of 450 N force) can be drawn as shown below:

Q: Find the Resultant Force in kN. Find the Angle opposite the resultant force (in degrees). Find the…

A:

Q: F1-500 kips 69⁰ 0.8 F3=250 kips 1 + F2 3 concurrent forces are acting on a point as shown. What is…

A:

Q: To test the strength of a 625 x 500-mm suitcase, forces are applied as shown. Take P = 116 N. 212 N…

A:

Q: The resultant loading force is 2.5 kN/m A O 09 O 5 07 3 m kN. 0.5 kN/m B 1.5 kN -1 m-

A: Solution.jpg

Q: Evaluate the magnitude and direction of the F1 action on the eyebolt if the resulting force applied…

A: Evaluate the magnitude and direction of the F1 action on the eyebolt.If the resulting force applied…

Q: The moment of the Force 40 N shown equal 12 Nim Determine the length of x- 40N 20 x 250 کرو Jio

A:

Q: Consider the pipe shown in (Eigure 1) Figure ▼ Part A Determine the coordinate direction angles a,…

A:

Q: Determine the angle made between the axes OA and AC.

A: The position vector of the point O with respect to point A is The position vector of the point C…

Q: Express Fas a vector in terms of the unit vectors i, j, and k. Determine the angle between Fand the…

A:

Q: force of 800 kN is applied at point B and is directed towards point F. The Force at D = 0 and does…

A:

Q: Q1/Compute the magnitude and direction of the resultant.

A: Draw the diagram of the given system. Calculate angle α, α=tan-172 mm135 mm=28.07° Calculate angle…

Q: a Determine the Force gg AC 6 Determine the Forde AB 2' + 8' 350

A: Given: To find: Force AB , AC

Q: Situation 4. Determine the magnitude and coordinate direction angles of the resultant force acting…

A: To find The magnitude and coordinate direction angles of the resultant force acting on A. Given…

Q: Using the figure, find the magnitude of the resultant force. Numbers in picture are: Orange: 236 Ib…

A:

Q: 4. Three vectors A = 2i+j-k, B=i+j-2k, and C= i +3j - k, where SB + C is perpendicular to A, the…

A:

Q: The second moment of area for the * following figure is

A:

Q: Determine the area of the shaded region. The value of b is 4 inches. Write the numerical value only.…

A:

Q: QI) Determine the magnitude and direction of F, so that If the resultant of the three forces act on…

A: Solution: The position of the resultant R is shown in the above figure, Angle made by the force F1…

Q: Which of the following is the angle that the resultant force makes with the positive y- axis?

A: GIVEN :- P= 2KN Q=4KN F=3KN Position vector of resultant force : R= -2i→-2j→-k→ so, position of…

Q: y 25 mm 20 mm 125 mm 2. A piece of sheet metal, with uniform thickness, is bent into the shape shown…

A:

Q: Find the angle between the planes x + y = 1 and 2x + y -2z = 2

A: Write the expression to determine the normal vector of both the planes. Substitute the value of…

Q: Using Mason's Formula, Find the T.F. R Y3 GI HI 3 3 H2

A:

Q: If P1= 400 N and P2 = 65O N, * Calculate EF, and EF, using x'and y'axises y y' x' P1 2. P2) 30

A:

Q: A fireworks show is choreographed to have two shells cross paths at a height of 117 feet and explode…

A: Given:h=117 ftθ=68o

Q: The force F acts on the gripper of a robot arm. The moments of F points A and B are 310N.m and…

A: The FBD for the robot arm is given below,

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.