F RAX F RAY F2 RDY The figure above is a pin-joint frame with angle 0 65° between members AF and AB. (Note that the diagram is not to scale). Given that the reaction forces at the support A are given by RAX 35kN and RAY = 70KN, calculate the forces in members AB and AF, denoted by FAB and FAF respectively. Enter your answers in kilonewtons (kN) correct to 2 decimal places in the boxes below: Enter FAB: kN Enter FAF: kN

Q: The uniform beam has a mass of 54 kg per meter of length. Determine the reactions at the supports.…

A:

Q: 68 lb/ft 34 lb/ft 34 lb/ft 548 ft Ib B 2.8 ft 2.8 ft

A:

Q: When the two forces are placed on the beam, the diameter of the steel rod (E-200GPa) BC decreases…

A:

Q: For the statically indeterminate beam shown in Figure 3, determine the reactions at the support A…

A: Indeterminate beam with half span loading, It is asked to determine the reactions at the support A…

Q: Draw a neat, fully annotated shear force and bending moment diagram, including the maximum in span…

A: The loading diagram is shown below. Hint : Horizontal distance of BD=3 cos45°=2.12 mVertical…

Q: The curved rod lies in the x-y plane and has a radius of 3 m. If a force of F = 80 N acts at its end…

A: Given Data : F= 80 N Radius = 3m Determine the moment of that force = 80 N about point O?

Q: determine the force in every member

A: Given Data  Determine the forces in each member of truss.

Q: 400 lb 400 lb 160 lb/ft 100 lb/ft MATHalino com 5 ft 5 ft 3 ft * 10 ft 6 ft *3 ft R1 R2 R3 R4 Figure…

A:

Q: Problem (9.2): The truss shown in Figure (9.25) is made of steel rods, each of which has a solid,…

A: The modulus of Elasticity in strain E=29×103ksi The shear stress,σy=36 ksi Cutting truss 1 - 1 and…

Q: Determine the bar forces and reactions in the truss shown in Figure 11.8a. Note that AE is constant…

A:

Q: Problem 5.2: The structural steel wide-flange beam shown in Figure (5.24) is a W10x60 section (See…

A: Allowable flexural stress = 28 ksi  Determine  a. Maximum moment about z-axis.  b. Maximum moment…

Q: 2/11 The two forces shown act at point A of the bent bar. Determine the resultant R of the two…

A:

Q: analyzes structural force, and writing bending moment

A: ###Determination  of structure force like SFD and NFD and Bmd### USING castigliano's   second…

Q: B.2. Elementary beam theory predicts that the axial bending stress ox in a prismatic beam is given…

A:

Q: A complete free body diagram must be included.

A: Step 1: Determination of reactions at A and B. I hope it will help you please give positive rating.…

Q: For the truss shown in the figure, P₁-12.7 kN and P₂-9.2 kN. Find the force in member AF in units of…

A:

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.