F |8 in. E 10 in. В C D 12 in, 12 in, 12 in.

Q: 300 mm 30° 300 mm 300 mm Can some one please label the projection of F and the rest of the…

A: Solution: The force vector F and uOA:

Q: Check for Plastic Section Modulus (Zx) and Plastic section Modulus (Zy) 50 150X50X25X2MM O150 25 25

A:

Q: Problem 4- The dam on Hydaway Lake on Liberty Mountain (not really sure if a dam exists) has the…

A:

Q: Angular dimensions measure the angle between. two arc O two objects O two circle O Two point O two…

A: Answer - Option e Two lines Angular dimensions measure the angle between two non parallel lines or…

Q: Determine the number of divisions required on the vernier scale, if it is combined with the main…

A: given- least count of main scale=0.5 mmleast count of combination of direct vernier=0.05 mm

Q: Q2- Find the centroid for the shaded area shown in the figure. (All dimensions in mm) 20 40 20 50 XA

A: Various shape property:

Q: Determine the x-coordinate (x-bar) of the centroid of the shaded area. (Use 3 decimal places) P=140…

A: Given Data  Find the x-coordinate of the centroid of shaded area.

Q: d = 4" %3D x' b = 4" %3D B = 8" %3D H = 8" h = 4" d = 4"

A:

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: E A F D 3 in. in. G -2 in. 1.5 in B

A:

Q: Locate the centroid (ĩ coordinate) coordinate) of the composite figure? 3 in 4 in 3 in 3 in

A:

Q: 100 mm 150 mm

A:

Q: Calculate the shape factor of the cross-section shown. 200 12 250 600 50 50 700

A:

Q: QUESTION 5 Which of the following represents the location of the horizontal plastic neutral axis (X,…

A: Solution Find the location of horizontal plastic neutral axis

Q: The shape factor for the uniform section shown below is 20 Î 20 + 50 50 * 50 50

A:

Q: Determine: a) Differential Area b)  Centroid distance along x and y axis   *use 3 decimal places…

A:

Q: 1. Locate the centroid of the folowing figures. 90 mm a) b) 90 4 in mm 3 in 120 mm 2 in 2 in 2 in A…

A:

Q: A 2in x 2in x 1/4in angle bar with a length of 24 inches has width-thickness ratio of

A:

Q: 0.5 in. 4 in. |0.5 in. -3 in.-

A:

Q: Shape PNA L5x3x1 -X x²/16 x x5/16 x¼ PNA k Wt. Table 1-7 (continued) Angles Properties Area, A Axis…

A: As multiple questions are asked and as per the guidelines only very first question will be answered.…

Q: 3. A 12m beam simply supported at 1.3m from both ends carries a uniformly distributed load of 18KN/m…

A:

Q: Q2- Find the centroid for the shaded area shown in the figure. (All dimensions in mm) 20 40 20 50

A:

Q: Determine moment of inertia about centroidal x-axis.

A: The specification of the W16 x 50 section as given,SectionDepthWidthWeb ThicknessFlange…

Q: 6Ocm 20 29 cm

A:

Q: answer this too please y bar put 3 demicals if possible

A: Centroid y = (A1y1-A2y2)/ (A1-A2)

Q: Draw the half sectional front and side view, as well as draw the top view of the object as shown in…

A: The half sectional front view, side view and top view of the object is provided.

Q: (1) a L₁ B P b C L2 C D

A:

Q: In the figure below, find the dAB GAB OCF E= 200,000MPA Area=200mm² P=36kN E 0.5m C 0.4m Area=625mm2

A: Data Given: Asked: Deflection in member AB Stress in member AB Stress in member CF

Q: - 4- पिक (17 b=260m- de-Sm h= 300m = 204N/m to 2onm M= <40kN b f=30kW

A: Given. Udl =20kn/m bending moment 40knm Point load 30kn Draw sfd bmd

Q: H, = 19 mm, G, 2.51, Pa 1.73 g/cm d, = 0 division, Gauge factor = 0.01 (mm/division) Dial Gauge Dial…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: how did e and de derived? show a solution

A: Given: Required: Show the calculation of e and DE

Q: 25mm 15 mm 90 mm 250 mm

A:

Q: how is A1 solved

A: Answer Area A1 is solved using  scientific calculator. Use 'X' in place of 'A1' in Scientific…

Q: Given the following: b=380mm d=530mm fc'=30MPA fy=320MPa Mu=650KN-m Determine As A. USE NSCP 2015,…

A: Given,

Q: For the given structural steel sections below, determine the following: a. The location of the…

A:

Q: 20 cm 2o cm 40 cm 40cm 20cm 80 cm

A:

Q: Total number of bags needed if each bag is 50kg (110lbs) and total weight of aggregates and water…

A:

Q: Calculate Q for a W10x15 cross section (A992).

A:

Composite Construction

Composite construction is the construction of structures in which two or more materials are used. Regarding structural engineering, composite construction is a construction where two materials are bound together in a technical manner such that both the materials act as a single unit to carry and transfer the load. The motives of composite construction are to increase the structural strength, make structures more aesthetic, and provide a sustainable environment.