13. A four-cycle six cylinder diesel engine of 4 % in boreand 6-in stroke running at 1200 rpm, has 9 percentCO, present in the exhaust gases. The fuelconsumption is 28 lb/hr. Assuming that 13.7 percentCO2 indicates an air-fuel ratio of 15 Ib of air to 1 ib offuel, calculate the volumetric efficiency of theengine. The intake air temperature is 60 deg. F andthe barometric pressure is 29.80 in of Hg.A. 83%B. 81%C. 87%D. 92%50

Answered: Image /qna-images/answer/b5c97a4b-f0e9-4a47-875e-4652fdf31adb.jpg

Answered: ext gases. 28 lb/hr. Assuming t n…

Engineering

Mechanical Engineering

ext gases. 28 lb/hr. Assuming t n air-fuel ratio of 15 e volumetric efficior Hicion

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I) C,H, is burned in an engine with a rich fucl-air ratio. Dry analysis of the exhaust gives the following volume percentages: CO2 = 14.95%, C,H,= 0.75%, CO = 0%, O2= 0%, with the rest being N2. Calculate: a) Air-fuel ratio b) Equivalence ratio
A Methanol pool fire shows a fuel mass loss rate of 0.01 kg/s on a load cell Estimate the heat release rate Assume a combustion efficiency of 08 The heat of combustion of Methanol can be obtained from the text book (Table 76) O A 160 KW O B. 20000 KW OC. 200 kW O D. 16000 kW QUESTION 2 Estimate the heat release rate for a keroene pool fires with a mass loss rate of 0 123 kg/s Assume combustion officiency 08 O A. 2000 KW O B. 200 kW OC 4250 kW OD. 34500 KW QUESTION 3 If the diameter of the kerosene pool fire from the above question (Question 2) is2 m, estimate the flame hoight of the pool fire. O A.04 m OB.4 46 m OCB0M O D. 42m
2. State one for dual combustion engine is 1 atmospheric and 60.3°C, rk=18; At the end of constant volume combustion process the pressure is 7695 KPa, ro=1.5 Base on one kg per cycle of a hot air standard with k=1.31, determine the a. P,V, and T@ each corner of the cycle b. efficiency c. mean effective pressure
(EVAP) operates with fuel anifold near each alve? ct to the stoichio- rottle, cruise con- conditions when ht cruising. ditions when full tic converter. is the least risky wes and runners, embling it, and g a crushed wal- n sing a chemical so it can be re- ump volume? lieve the static g the fuel lines pump fuse and 10. An inject stricted with deposits can be done using a(n): oscilloscope. pulse tool. digital multimeter. fuel line release tool. d. Questions ASE Technician A/Technician B Style 1. Tech A says that most electric fuel pumps are now mounted inside of the fuel tank. Tech B says that fuel flows through the center of the electric pump and is used to cool the pump. Who is correct? aTech A b. Tech B Both A and B d. Neither A nor B that has a bleed sing the excess tool to release In and drop test to see if the injector is re- 2. Tech A says that the stoichiometric ratio is 14.7 gallons of air to 1 gallon of fuel. Tech B says it is 14.7 lbs of air to 1 lb of fuel. Who is correct? a.…
Compression ignition engine is havinga compression ratio of 14 and cut off ratio of 2, the specific heat ratio is 1.4, then the efficiency of the engine is approximately O a. 69% O b. 59% O c. 49% O d. 70%
The return air temperature of the room is 78F and cooling system load is 48,000 Btu h (sensible). How much air flow (in CFM) is required for proving 58F as the supply air temperature?
2. Which one is essential for combustion of fuel? C. correct fuel air ratio D. all of these * A. oxygen to support combustion B. proper ignition temperature
which humidity would have a lower terminal velocity, 5% 0r 80%?
Illustrate, Label and Discuss the following on fuel processes a. Thermal Cracking
Determine the air fuel ratio on a molar basis for the complete combustion of octane , with theoretical amount if air.
Given Doy Bulb ī = 20°C Wet BulbT 14°C Ar Pvess. = 101320 Pa %3D Dow Point 10° Relative Humidity actoal Ve Waat 52.5% ) what is the Speaitic Humidity ? ) what is th Air Devsity?
Do you think heating-humidification process is of utmost importance for Comfort AC system for country same as the Philippines?