Explain the symbols given below

Q: can explain D,E,F more clearly also

A: d ) The force required for circular motion is the centripetal force, which is provided by the lift:…

Q: Maybe someone can show the solution for this problem and be hand written pls.to be easy to…

A:

Q: Describe the method of superposition?

A: Method of superposition: It is a method used to determine the deflection and slope in a beam due to…

Q: why bare pipe has 0% efficiency and full covered insulate pipe has more efficiency

A: A thermal insulator has a low thermal conductivity and is a poor heat conductor. To reduce heat loss…

Q: Convert to cis form

A: Conversion to cis form.

Q: material is not ceramic material. * O Aluminium oxide O graphite О НА O none

A: It is required to determine which of material is not ceramic

Q: How does a pressure control solenoid regulate transmission pressures? (50 - 80 words)

A: This question is based on the concept of pressure control solenoid.

Q: Describe briefly what is stoichiometric from point defects point of view.

A: These are the point factors that don't disturb the stoichiometry of solid matter.Stoichiometry…

Q: Define 'power'.

A: It can simply defined as the amount of work done per unit time. Or the rate of time of doing work or…

Q: The indices for the direction shown in the figure are: Select one: O a 10] O b.[210 O a. 021

A: For the given direction,

Q: Thermosetting plastic materials have the cost saving advantage in that they can be injection molded…

A: Thermosetting plastic materials have the cost-saving advantage in that they can be injection molded…

Q: Assuming that aluminium has an embodied energy of 211.51 GJ/tonne. Calculate the lifecycle…

A: Given data: Aluminum embodied energy, E = 211.5 GJ/tonne = 211.5×106 kJ/tonne Source Estimated…

Q: Give at least 3 examples of measures of position

A: The 3 examples of measures of position are listed below: 1. Percentile: The percentile is a score or…

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: Represent the following combinations of units in the correct SI form using an appropriate prefix:…

A: The given units are km.uN But the correct SI units shall be N.m

Q: State four alloying elements which are combined together with iron and carbon in the manufacture of…

A: A typical allowing elements of the HSS other than Fe and C are as below: 1 Chromium (3.8%), It…

Q: Please DRAW PV-TS Diagrams

A: Given:  m = 2 kg P = 172 kPa T1 = 32°C T2 = 182°C

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

A:

Q: 1) Materials that have high binding energy have high/low strength and melting temperature. Materials…

A: 1) high 2) large,large,lower

Q: Compare modulus of resiliance for Ti alloy and Al alloy

A: Solution:   Yield point or the yield stress of an alloy is the point or the stress at which a…

Q: Which of the following situations has the greatest impulse? A very large collision force acting over…

A: Impulse: The product of the applied force with the time duration of acting is known as impulse. The…

Q: (b) The mass of the object suspended at G is 100 kg, as demonstrated in Figure Q5(b). Determine the…

A:

Q: Why does Qc = -hA(deltaT) and not just hA(deltaT)?

A: There are two expressions for the heat to be condensed.The difference between the two expressions…

Q: It's saying this is not correct. Thank you for your help.

A: We apologize for the inconvenience. The corrected solution is given below.The mass of water is .The…

Q: Convert into engineering notation using si prefixes or si symbols with 3 significant digits…

A: Values are given as 0.0000035674 amps176234.178 volts

Q: what is CAE?

A: CAE” Computer Aided Engineering” comes under FEA(Finite Element Analysis).It is used to simulate the…

Q: hat metallic properties do materials have?

A: Given Data : Metallic properties

Q: Determine the degrees of freedom of the mechanism shown in Figure 1. Universal joint Prismatic joint…

A: Here we will use mobility formula to find degree of freedom of mechanism. For that we will find no.…

Q: Explain the three geometric expressions described in the class that satisfies Bragg's law?

A: Bragg's law, also known as Wulff–condition Bragg's or Laue–Bragg interference, is a kind of Laue…

Q: me and explain three factors that affect the resistivity of metals

A: