Explain the relationship between the size of the filter elements and frequency and state the disadvantages brought about by the very high switching frequency. Explain whether it would be more useful to control a DC chopper at high frequency or low frequency

Explain the relationship between the size of the filter elements and frequency and state the disadvantages brought about by the very high switching frequency. Explain whether it would be more useful to control a DC chopper at high frequency or low frequency

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Related questions

Q: What is the use of DC-DC boost module 0.9-5v to 5v? How does it work?

A: A DC-DC boost converter module (boost converter) is a DC-DC power converter module that boosts…

Q: What is Frequency Modulation? Draw the waveforms.

Q: A step up chopper has 175 volts as input and the output required is 325 volts. If the non-conducting…

Q: Discuss and explain how filter circuits for AC and DC power supply works.

A: AC circuit have a finite frequency and time period. AC filters are used to block or pass the certain…

Q: Describe the process of Filteration?

A: In filtration solid material which is generally in suspension form are separated from the liquid…

Q: What Is frequency modulation and demodulation? Describe their importance and how they work.

A: Given: Frequency modulation and demodulation

Q: What is equation of the demodulator? advantages and disadvantages of DSB-SC over DSB-AM?

A: Demodulator The process of extracting an original message signal from the modulated wave is known as…

Q: nethod.

A: Here it is asked to draw the block diagram of Phase demodulator using frequecy discriminator method.…

Q: What does increased signal to noise ratio mean?

A: Signal to noise ratio : Signal to noise ratio is denoted by S/N ratio it is present in both analog…

Q: What do you think is the main disadvantage of a Clipper circuit over a Clamper Circuit?

A: The disadvantage of a Clipper circuit over a Clamper Circuit can be explained as follows.

Q: State and prove maximum power transfer theorem for DC circuits.

A: Maximum power Theorem: It state that, A resistive load which is connected to a dc network, receives…

Q: If the voltage dropped over a resistor directly connected to a signal generator... changes with…

A: It is known that the voltage does not depend on the frequency for purely resistive impedance whereas…

Q: E5.3 Compute V, in the circuit in Fig. E5.3 using superposition.

A: The superposition theorem state that the sum of response of individual sources acting alone is equal…

Q: What is signal to noise ratio?

A: SNR or sign to-commotion proportion is the proportion between the ideal data or the force of a sign…

Q: Q#3 : How transient stability limit can be increased?

A: Methods to improve transient stability : Using high speed circuit breaker : It increase the…

Q: A DC chopper has 225 volts as input and the output required is 425 volts. If the non-conducting time…

A: The input to chopper is 225 v. output of chopper is 425 V. So the chopper used is boost st chopper.…

Q: Why is DC COUPLE recommended when measuring a low frequency signal?

A: Coupling is the way to defined that how the circuits are interconnected with each other. DC…

Q: what should be the operating frequency to have a high frequency gain of 30 % lower that the mid…

A: The circuit diagram is given as We know that the frequency response of opamp is like a low pass…

Q: Discuss the importance of Nyquist plot technique in control systems.

A: Brief description: In the given question they want to know the importance of the nyquist plot…

Q: Ex. 1915. An Arduino analog input voltage is 3.160 volts. Arduino PWM output pin drives a low-pass…

Q: (i) A chopper circuit drives an inductive load from 120 DC supply. Given the load resistance as 6 0,…

A: Input to chopper circuit = 120 V DC. Output average current = 52.5 Amp Output resistance /load…

Q: What is the benefit of using two pulse transformers to drive the SCR of a single-phase bidirectional…

A: the benefit of using two pulse transformers to drive the SCR of a single-phase bidirectional AC…

Question

Explain the relationship between the size of the filter elements and frequency and state the
disadvantages brought about by the very high switching frequency. Explain whether it would be
more useful to control a DC chopper at high frequency or low frequency

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is Frequency Modulation? Draw the waveforms.
Using Ai leads to downvote 451. Discuss the principles of chopper-stabilized filters.
A step up chopper has 175 volts as input and the output required is 325 volts. If the non-conducting time of thyristor is 175 micro seconds-compute. ) Chopping frequency. ii) If the pulse width is (1/4)th of that in case () for constant frequency of operation, find the new output voltage. ii) If the frequency is increased 20% of that in case (i) keeping the conducting time constant, what is the new value of k and output voltage of the chopper.
What is signal to noise ratio?
A/Q20
Discuss and explain how filter circuits for AC and DC power supply works.
1. The purpose of the Lag Compensator is: I. Improve the study state response of the close system. II. Speed up the transit response. III. All the above. IV. None of the above. 2. In the Lead Compensator: I. Z > P. II. Z < P. III. Z = P. IV. None of the above.
Describe the process of Filteration?
Mark the good definition
A DC chopper has 225 volts as input and the output required is 425 volts. If the non-conducting time of thyristor is 225 micro seconds, compute. i) Chopping frequency. ii) If the pulse width is (1/5)th of that in case (i) for constant frequency of operation, find the new output voltage. iii) If the frequency is increased 25% of that in case (i) keeping the conducting time constant, what is the new value of k and output voltage of the chopper.
Q.) A dc chopper in figure has a resistive load of R = 10Ω and input voltage of V = 200V. When chopper is ON, its voltage drop is 2 V and the chopping frequency is 1 kHz. If the duty cycle is 60%, determine – Average output voltage– RMS value of output voltage - Effective input resistance of chopper – Chopper efficiency.
a) what should be the operating frequency to have a high frequency gain of 30 % lower that the mid band gain. Assume a DC gain of 100 dB & Dc cut – off frequency @ 15 KHz.?