Explain the following code and based on the following circuit diagram what willbe the output?⠀⠀⠀⠀⠀ ⠀⠀⠀⠀⠀ ⠀⠀⠀⠀⠀ ⠀⠀⠀⠀⠀ ⠀⠀⠀⠀⠀∞ UNOint timer = 100;void setup() {for (int thisPin = 2; this Pin < 8; thisPin++) {pinMode(thisPin, OUTPUT);}void loop() {for (int thisPin = 2; this Pin < 8; thisPin++) {digitalWrite(thisPin, HIGH);delay(timer);digitalWrite(thisPin, LOW);}for (int thisPin = 7; thisPin >= 2; thisPin--) {digitalWrite(thisPin, HIGH);delay(timer);digitalWrite(thisPin, LOW);fritzing

The given code is written in Arduino's programming language, which is based on C/C++. Let's break…

Explain the following code and based on the following circuit diagram what will be the output? } an tomb int timer = 100; void setup() { for (int this Pin = 2; this Pin <8; this Pin++) { pinMode(thisPin, OUTPUT); ∞O UNO } void loop() { for (int this Pin = 2; this Pin <8; this Pin++) { digitalWrite(thisPin, HIGH); } delay(timer); digitalWrite(thisPin, LOW); for (int thisPin = 7; this Pin >= 2; thisPin--){ digitalWrite(thisPin, HIGH); delay(timer); digitalWrite(thisPin, LOW);

Explain the following code and based on the following circuit diagram what will be the output? } an tomb int timer = 100; void setup() { for (int this Pin = 2; this Pin <8; this Pin++) { pinMode(thisPin, OUTPUT); ∞O UNO } void loop() { for (int this Pin = 2; this Pin <8; this Pin++) { digitalWrite(thisPin, HIGH); } delay(timer); digitalWrite(thisPin, LOW); for (int thisPin = 7; this Pin >= 2; thisPin--){ digitalWrite(thisPin, HIGH); delay(timer); digitalWrite(thisPin, LOW);

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Explain the following Arduino Code 10 void setup() { 11 pinMode (13, OUTPUT); 12 13 void loop() { digitalWrite(13, HIGH); 14 15 16 delay(1000); digitalWrite(13, LOW); delay(1000); 17 18 19 }
5- Write a C code that generates a 100 cycles only of waveform at variable frequency where the output frequency is given by: foutput = 5 + n Hz, where n is the Cycle Number n= 0,1, 2..... .99. The output is available from RB10. Given that Fcy = 50 MHz.
OR Ex3// A. B. A. B. module OR (a, baig) Follow the same steps, but use the gates, and each gate has its own table for the following gates: input a, b's 1_NAND 2_NOR 3_XOR Dut put y's assi gn y= a OR Lend modale
1) Write three boolean expressions for each of the output variables A, B and C. 2) Write the name of circuit which is represented by this table 3) Which type of gates are used to construct this circuit? Do 1 0 0 0 0 00 0 D₁ D2 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 Inputs D3 0 0 0 1 0 0 0 0 D4 0 0 0 0 1 0 0 0 D5 0 0 0 0 0 1 0 0 D6 0 0 0 0 0 0 1 0 D7 0 0 0 0 0 0 1 A 0 0 0 0 1 1 1 1 Outputs B 0 0 1 1 0 0 1 1 C 0 1 0 1 0 1 0 1
* Refer to the logic gate symbols shown below. What type of logic gate is gate C? B. C. :D D. D E. Đ F. OR gate AND gate O NOT gate O XOR gate Refer to the logic gate symbols shown below. What type of logic gate is gate F? * Đ B. c. D D. D E. D F.D NOT gate XNOR gate XOR gate NAND gate What logical reason/s can you give why NAND and NOR gates are considered universal gates? they can appear anywhere in the circuit they cannot be partial they can produce universal operation they can imitate function of other gates
Answer these questions please. Ctr
Q.3) Design a JK FF using: a) an SR FF and minimum gates. b) a D FF and minimum gates. c) a TFF and minimum gates.
Explain the given arduino code
What is the rule for an XOR gate? A. When A is not equal to B, the output goes “LOW” B. When A is equal to B, the output goes “HIGH” C. When A is not equal to B, the output goes “HIGH” D. None of the above.
1. An ocean front restaurant has purchased several automatic windows, which are designed to close whenever they receive a logic'1'. The restaurant wants the windows to close when it's either cold(c-1) or both windy(w=1) and raining(r=1). Create a simple digital circuit which determines when the windows should be closed using only two gates. Suppose a technician hired by the restaurant designed the following Boolean expression: (r'+c)'w+c . Using Boolean algebra, prove that both expressions implement the same function("are equivalent"). . Which expression would you use in the final design? Why? 2.
Based on the Tinkercad circuit accessible from the link below, complete the following activities:https://www.tinkercad.com/things/c1qtxCkOuBW Code is, // C++ code// const byte LED_PIN = 13;const byte METER_PIN = A4; void setup(){ pinMode(LED_PIN, OUTPUT); pinMode(METER_PIN, INPUT); Serial.begin(9600); startTimer();} void loop(){ } void startTimer(){ noInterrupts(); interrupts();} ISR(TIMER1_COMPA_vect){ digitalWrite(LED_PIN, digitalRead(LED_PIN) ^ 1);} 1. Complete the code in a way that LED blinks every 2 seconds.2. Change the startTimer method to accept a double value called timerFrequency, which representsthe frequency of the timer. Change the startTimer function so that it uses the value of this parameterto calculate and set the correct values for the OCRx and TCCRx registers.3. Use the potentiometer sensor connect to pin A4 to enable users to configure the timer frequency. Plsease share the final code only.
Using the sim8085 write the following code: In a sensor network, three pressure sensors are connected which gives the reading of 4 psi, 8 psi and 10 psi. All the sensor readings are to be summed up and store as a single reading