Explain in deatil prime cause of fire and explosion in paint tecghnology

Q: How to Identify valence electrons and core electrons ?

A: It is to be mentioned how to identify the valence electrons and core electrons.

Q: Explain what are the application of diffusion with each the following: Food Industry Food…

A: The process of diffusion in mass transfer refers to the movement of solute molecules in a solvent…

Q: Study how heak treakwent process Cannealing normalizing and hardenine) are effecr of Shanged tue…

A: Effect of heat treatment on "Low Carbon Steel" is asked.

Q: Can a near-perfect separation be made with gas permeation?If not, why not?

A: Gas permeation technology uses porous membrane for the separation.

Q: 4) What is the difference between stress corrosion cracking and corrosion fatigue? Did polymer…

A: Given data 4) What is the difference between stress corrosion cracking and corrosion fatigue? Did…

Q: Which of the following is true? A Hydrogels have a network structure and can soluble in water. B…

A: Hydrogels are polymeric materials that are formed from natural or synthetic polymers. These polymers…

Q: For type of mixture is osmosis well suited?

A: The mixtures for which osmosis process is suitable is to be mentioned.

Q: Determine whether an example is spontaneous process (SP) or a non-spontaneous process (NSP). 6. ball…

A: Given data 6.ball rolling uphill 7.removing stain from a cloth 8.ripening of fruits 9.flow of heat…

Q: What material of storage tank can be best used in storaging polyethylene glycol 400?

A: Polyethylene glycol is produced by the poly condensation reaction of ethylene glycol compounds with…

Q: Example of material balance of absorption?

A: An example of material balance of absorption is to be mentioned.

Q: 11. Write the type of errors in Gas Permeameter method

A: The gas permeameter is used for measuring the permeability. Permeability is defined as the property…

Q: Write in brief about main engineering problems in chlor-alkali industry

A: The main engineering problems in the Chlor-alkali industry are to be mentioned.

Q: Determine their type of nano material and briefly discuss one application for Nano-Titanium Dioxide,…

A:

Q: in Precipitation titration curves, As the concentration of the titrant decreases the sharpness of…

A: Precipitation titration is a type of titration in which the analyte and titrant react together to…

Q: Research about any of the following alloys and give their properties and composition. Choose at…

A:

Q: Fuel-oxidant ratio affects _____________ and _______________. flame's temperature, viscosity flame's…

A: Answer: Flame`s temperature and explosive limit pressure

Q: Compare Thermogenic, Biogenic & Abiogenic formation of natural gas

A:

Q: Explain reaction of extraction of cooking oil?

A: Solvent extraction is one of the versatile chemical oil extraction method in which a solvent is used…

Q: The scientist name for Chemical Solvent Process for sweetening is

A: Sol. Sulfinol Process

Q: What can reduce the temperature of stack gases in a furnace? Is it using pure oxygen, separating…

A: Operating your boiler with an most desirable quantity of extra air will reduce warmth loss up the…

Q: None

A: Reinforced concrete is a combination of concrete and reinforcing steel bars.  A sample figure of a…

Q: Why does boiling point in IMF important?

A: The importance of the boiling point in IMF is to be mentioned.

Q: Is there an alternative process for reflux heating? This is about catalyst preparation

A:

Q: How membrane separation process can be relate to the fundamental of heat/mass transfer?

A: The membrane separation process is a very important water treatment process in which the mass…

Q: what is the common problem and solution of BTX extractive distillation?

A: BTX extractive distillation is used to remove benzene, toluene and xylene from refinery, petroleum…

Q: What can be the point of improvement in packed towers in absorbing nitrogen oxides?

A: Introduction: Packed towers: The packed tower is a non-stop contact kind of fuel-liquid mass…

Q: Which of the following stament is true for the used additives for the thermoplastics? Fillers…

A: Thermoplastics are plastic polymers that become soft when heated and hardens on cooling. Additives…

Q: What is specific objective for Waste Vegetable Treatment to produce electricity

A: The overall objective for the assessment carried out for waste management is described below: a) To…

Q: How metal impregnated ceria works as a catalyst supported on monolith in catalytic converter?

A: Introduction: A catalytic converter is an exhaust emission manage tool that converts toxic gases…

Q: Describe about MORTON SALT?

A: Morton salt is a type of table salt which do not forms clumps together. The salt contains magnesium…

Q: Discuss the uses of thermosets in the biomedical industry.

A: Thermosets, also known as thermosetting polymers are polymer materials that have the property to…

Q: One of the Types of emulsions is  1- Oil In Water 2- Tar in Oil 3- Gas in Oil

A: there are three types of emulsions which are water-in-oil (W/O), oil-in-water (O/W), and…

Q: Give 3 example of radiation process in nanofluid?

A: Given data Give 3 example of radiation process in nanofluid?

Q: What are key advantages and disadvantages of using ozone versus chlorine for disinfection

A: Advantages of ozone: 1) Ozone is the best component for killing protozoa, bacteria, and viruses. 2)…

Q: n SPME for HPLC, analytes are desorbed from the fiber into solvent that is injected into the HPLC…

A: SPME also known as Solid Phase Micro Extraction is an equilibrium sampling method and can be used…

Q: Distinguish between saline carbides, metallic carbides and metalloide carbides.

A: In chemistry, a carbide usually describes a compound composed of carbon and a metal. In metallurgy,…