Explain and show conflict points of Round about

Q: To produce 1 cubic yard of air-entrained concrete with target slump of 2 inch, what is the required…

A: Air-entrained concrete contains billions of microscopic air cells per cubic foot. These air pockets…

Q: Q4. Why disposal of hazardous waste is not suitable by land filling?

A:

Q: Consider the following beam ABC, loaded as shown in figure. The cable passes over a small…

A: For given arrangement,W= 10 kNTo find the maximum shear force in the beam AB

Q: The coefficient of permeability of fine sand is 0.012 cm/sec at a voids ratio of 0.57. Estimate the…

A: Given data, Coefficient of permeability, k1= 0.012cm/s Void ratio, e1= 0.57 e2= 0.72, K2=?

Q: Topic: FLAT SLAB Determine the total dead load (in kPa) of the following different types of slab if…

A:

Q: Indicate the total project duration and Critical Path.

A:

Q: The unsteady flow of glycerin is such that at A it has a velocity of VA = (5 t/2) m/s, where t is in…

A: VA = 5t1/2 m/s To find acceleration at x = 0.3 m and t = 1 s

Q: Fill out the blanks in following statement. The removal of substances from water is accomplished by…

A:

Q: b) The beam of length L is embedded at its left end and simply supported at its right end, and a…

A: The beam of length L is embedded at its left end and simply supported at its right end w(x)=w0…

Q: A canal has designed to supply the irrigation needs of 1000 ha of land growing rise of 140 days base…

A: Given data, For rice :- Area irrigated A1= 1000ha B1 = 140 days  D1= 126cm= 1.26m For wheat :- B2=…

Q: What type of concrete additives (two additives each) would you suggest for casting (a) the same…

A: a) To accelerate the rate of strength of concrete production or to decrease concrete curing…

Q: Explain how to layout compound curve . * Provide astep by step explanatib n-

A: To explain about compound curve

Q: Draw the shear and moment diagram of the given beam using any method. 50 kN 15 kN/m 150 kN-m B C -6…

A:

Q: A rectangular beam is supported at both ends. It carries two concentrated load of 30KN, a clockwise…

A:

Q: An isosceles triangular gate with base of 6 m and height 4 m is at a depth of 1 m from the free…

A: given  b=6m h=d=4m a=distance between free surface to top of vertex = 1m Hcp=?

Q: 3. A pipe on a horizon reducing bend is used at a pressure in the incoming p force (and its…

A:

Q: What is the surface area (m²) of settling tank used for design discharge of 1.5 m³/s? (Assume design…

A:

Q: Explain what is project close out?

A: The term project closeout in construction is the last stage of a construction project and an…

Q: A rectangular wooden beam has a span of 6 m. and carries a total uniform load of 25 kN/m including…

A:

Q: The three reservoirs A, B and C are connected by pipelines A, B and C respectively. the elevation of…

A:

Q: Forest areas usually have freshwater ponds and lakes in which small animals such as crayfish,…

A: Given, For prototype(fresh water) μwater = 0.001 kg/m-s  ρwater=999kg/m³ For model (glycerine) Vm=…

Q: A pump helps bring oil (SG = 0.8) to reservoir D from reservoir A at 235 liters per second. The…

A:

Q: Problem 1 - 29 A vertical cylindrical tank with a diameter of 12 m and a depth of 4 m is filled with…

A:

Q: 8 k/ft 5 k/ft 3. Draw the moment diagram using method of superposition. 6 ft 9 ft

A:

Q: AW16X100 needs båse plate (A36 steel) to support dead load of 320 Kib and live load of 240 Kib. The…

A: The given data is: Dead load=320 kip Live load=240 kip

Q: A 84-mm-diameter siphon is drawing oil (SG = 0.85) from an oil reservoir, as shown in the figure. If…

A: Bernoulli's theorem assumptions: The flow is incompressible. The flow is steady( Pressure, density,…

Q: What are Relevant Events?

A: Relevant event is defined as the delay which effect the completion date of the project. This delay…

Q: Determine the force of the DE member (FDE) of the truss and state if the member is in tension or…

A: The given data is: P1 = 10 kN P2 = 20 kN

Q: ve me right solution ur

A: Draw free body diagram Calculate the total deflection  -∆1=PL33EI+PLhEI×Lb=PEIL33+L2h

Q: A laminated wooden beam supports a uniform distributed loading of 12 kN/m. Allowable shear stress is…

A:

Q: Define Unilateral Change Orders.

A: A unilateral change order/modification refers to a contract modification that will be signed only by…

Q: A proposed highway has intersection angle (1) 40°15 28. The highway design engineer, attempting to…

A: Given data  Intersection angle = 40∘15'28" Degree of curvature D=9∘ point of inter section…

Q: 25. Find the distance in nautical miles between Athens and Rome. Athens is located at 37°59'1.68" N…

A: Given:- The latitude of the Athens = 37°59'1.68" N The longitude of the Athens = 23°43'39" E The…

Q: Explain the Bharkhausen criteria USE DIAGRAMS

A: Bharkhausen criteria- The Barkhausen stabilization process is a mathematical requirement used…

Q: If the moment of inertia of the thin strip of area about the x-axis is 2.71(10) mm“, determine the…

A: Moment of inertia is used to measure or quantify the amount of mass located at an object's…

Intersection Design

An intersection is a location where two or more roads or railways meet or join. The traffic movement is controlled at the intersection that depends on its design and type. It governs the operation, efficiency, speed, capacity, and safety of the highways, airways, and railways. The movement of the pedestrian causes hazards and delays at the intersection.