Experiment No. (16): Shift Registers 2020/2021 3) How many clock pulses needed to make the foll actions? a) Serially shifting a byte of data into a shift register. b) Parallel loading a byte of data into a shift register synchronous load.

Q: Mention steps required to read a word from memory in the 4 x 3 memory circuit shown in Figure

A: Given: Mention steps required to read a word from memory in the 4 x 3 memory circuit shown in Figure…

Q: ) What is modulus value that should be used in a PIT clock system that is running at 24 MHz to…

A: Answer : i attached an image please have a look once.

Q: } The memory space of an 8085A based microcomputer consists of one 8K*8 bit EPROM starting from the…

A: Answer: I have given answered in the handwritten format in brief explanation.

Q: (Could be more than one) Select all of the registers listed below that are changed during EVALUATE…

A: Changed Registers During FETCH INSRUCTION are - MAR \sIR \sPC Step FETCH INSTRUCTION - When the…

Q: 1. Which datapath elements are accessed if "add" is executed? (choose from: instruction memory,…

A: Note: As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: -2) a) type a double-loop delay subroutine part. b) in this double-loop delay subroutine, calculate…

A: Q-2) a) type a double-loop delay subroutine part. b) in this double-loop delay subroutine, calculate…

Q: does program A require? b. The following measurements have been made on two different computers…

A: Solution 1 :- program a runs in 10 seconds on a machine with a 100 MHZ clock. how many clock cycles…

Q: mips assembly question how would I get an output of: 0xffffffdd using lb (load the byte) stored in…

A: Solution:--   1)As given in the question it is required for the solution which has to be provided in…

Q: ISC-V instruction) Write the following machine code in hex format(0xhhhhhhhh):   1) jalr x18,…

A: Line 1: 0x00000000:0x8e080000 [Loop: lw $t0 0($s0) => I(op:35(lw) rs:16(s0) rt:8(t0)…

Q: 4. Briefly describe the purpose of each T state listed: (a) T (b) T2 (c) T3 (d) T. (e) Tw

A: State Transition Diagram describes μp’s internal operations, where the circle representsthe states…

Q: a) Four EPROMS are connected together, each one has 11 address input and 8 data output What is the…

A: b) The transistor works in the switching mode ( ON/OFF). So, it is like putting a switch at pin 7,…

Q: (i) Draw and explain the control word register of 8255 PPI for BSR mode. (ii) If the bit PC4 must be…

A:

Q: If the max value of the counter is Ox00394391 and the bus clock frequency is 24 MHz, what is the…

A: Below is the answer with calculation:

Q: WHAT IS THE ADDRESSING MODE OF THE FOLLOWING INSTRUCTION ADD AX,BX Select one: a. IMMEDIATE…

A: ANSWER: D Explanation: Register Addressing Mode

Q: What happens if multiple interrupts occur in Interrupt-driven 1/0 using vectored interr

A: Due to bartleby guidelines, I can only answer the first question.

Q: 11. a. Draw flowchart of IAS operation for the following pair of instructions located in address…

A: Answer: a) The flowchart of the instruction goes this way:

Q: 5) A switch-tail counter (also called twisted ring counter, Johnson counter) uses the complement of…

A: Using D flip flop, Johnson counter working is explained along with timing diagram upto 5 clock…

Q: Question 2: The program needs 323 µsn delay. Plan this delay program and write using assembly.…

A: Code :   Instructions T-states for execution   Move BX, Count 4 L1: DEC BX 2   NOP 3…

Q: (c) Briefly discuss with diagrams as required, the "memories" in the PICFxxx series of…

A: In PIC micro-controller there are two type of memories used i.e program memory and data memory.…

Q: ) Draw and explain the control word register of 8255 PPI for 1/0 mode. ) If Port A is used for…

A: ANSWER:-

Q: c) List down FOUR categories of user-visible registers and describe about each category.

A: It is the one of the type of registers which is visible to programmers. These registers can be…

Q: (10) Draw ladder diagrams that satisfy the repeatable timing behavior shown in Figures (6-a) and…

A: Answer: I have given answered in the handwritten format in brief explanation

Q: What is the addressing mode of the following instruction?

A: what is the addressing mode of the following instruction\ SBB CX,[BX+SI+200]

Q: 1) Using all the given DLX handouts, give a detailed list of all the relevant control signals and…

A: Answer :   Instruction Description Format Opcode Operation (C-style coding) SUB subtract R 0…

Q: (i) What is Timing diagram? (ii) Draw the Read Cycle Timing diagram for minimum mode of 8086…

A: 1) timing diagram is used to show the execution of each instruction with respect to time.It…

Q: 8-bit register contains the Hex value 58. What is the register value after an arithmetic shift…

A: Hex number= 58  1 ) after logical shift right  Convert Hex number into binary  (58)16 =(01011000)2…

Q: Q.3 a) Four EPROMS are connected together, each one has 11 address input and 8 data outpu. What is…

A: a) Memory of EPROM = 2^(input) * output     Here we have 4 inputs , hence Memory = 4* 2^inputs  *…

Q: a) Serially shifting a byte of data into a shift register. b) Parallel loading a byte of data into a…

A: A) A byte is is the size of 8 bits so the serially shifting a byte of data take 8 clock pulses. B)…

Q: What happens if multiple interrupts occur in Interrupt-driven l/O using vectored interr

A: because of guidelines of Bartleby I can only answer first question.

Q: What is the maximal length of bit pattern associated with a 6-bit linear feedback shift register?

A: Given: What is the maximum length of bit pattern associated with 6 bit linear feedback shift…

Q: (a) Draw pipeline diagram (FI öné memöry port för the föllöwing instrüčtions! MOV [1234], 035 ADD…

A: The following is the solution

Q: Question 1: Logic Path and Delay A. Calculate the time to execute the following instructions. B.…

A: for addi  addi accesses instruction memory once, register read or write twice , ALU once, adder once…