EXERCISES Exercise-1: Design a PLC program and prepare a typical I/O connection diagram and ladder logic program for the following motor control: ▪ A motor must be started and stopped from any one of three start/stop pushbutton stations. . Each start/stop station contains one NO start pushbutton and one NC stop pushbutton. Motor OL contacts are to be hardwired.

EXERCISES Exercise-1: Design a PLC program and prepare a typical I/O connection diagram and ladder logic program for the following motor control: ▪ A motor must be started and stopped from any one of three start/stop pushbutton stations. . Each start/stop station contains one NO start pushbutton and one NC stop pushbutton. Motor OL contacts are to be hardwired.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The preferred method for applying the field excitation voltage uses a field relay which operates on the principle of A. speed application. B. time application.C. angle application. D. thermal application.
H.W: What instruction would you select for each of the following discrete input field devices to accomplish the desired task? (State the reason for your answer.) a. Turn on a light when a conveyor motor is running in reverse. The input field device is a set of contacts on the conveyor start relay that close when the motor is running forward and open when it is running in reverse. b. When a pushbutton is pressed, it operates a solenoid. The input field device is a normally open pushbutton. c. Stop a motor from running when a pushbutton is pressed. The input field device is a normally closed pushbutton. 33
multiple choice question.
True or False False True Since insulation required is less, Star Connection can be .used for long distances Star Connections are often used in applications which .require high starting torque When normally open type contacts are actuated, they disrupt the power supply .through them In order to reverse 3 phase motor we should switch all phase with each other In PLC system Wiring makes .the rule AC 3 phase motor can be installed to PLC output pin Via contactor
A motor can be turned on when a momentarily pushbutton A or B is pressed.Another pushbutton C is used to turn off the motor. The motor is equipped withoverload relay. With the implementation of holding mechanism (SETRESET/KEEP), design a PLC program ladder diagram for this system
Exercise-2: Design a PLC program and prepare a typical I/O connection diagram and ladder logic program for the following motor control: W Three starters are to be wired so that each starter is operated from its own start/stop pushbutton station. . A master stop station is to be included that will trip out all starters when pushed. . Overload relay contacts are to be programmed so that an overload on any one of the starters will automatically drop all of the starters. . All pushbuttons are to be wired using one set of NO contacts.
A)- Explain the trade-offs between relays and PLCs for control Applications. B)-Observe what happens when the buttons are pushed: (1 PB1 oto PB2 M2 HH M1 * Fill in the table: LAMP PB2 Off PB2 On PB 1 Off M1 OF OB LAMP PB1 On
3. Describe working of different proximity sensors used in a PLC.
21.a. What type of circuits are present on an axis logic card for a stepper motor system and are used toaccelerate and decelerate a motor?A. Timing circuitsB. Main oscillator circuitsC. Ramp circuitsD. Bias circuits21.b. A scaling or header plug is used on some brushless motor drive systems toA. connect the tachometer to the drive.B. divide the output pulse train.C. connect the front panel indicator lights to the drive.D. set the current limit of the drive.
7
"Electrical Machines/ I need clear and detailed answers to all the questions, preferably in a clear and concise manner."
Write a Ladder Logic PLC program for each of the following scenarios. Label all contacts and coils in the PLC program.