Exercise In a certain application, a signal source having 60 kl of source impedance, Rs, produces a 1 V,ms signal. This signal must be amplified to 2.5 V,rms and drive a 1 kN load. Assuming that the phase of the load voltage is of no concern, design an operational amplifier circuit for the application. Hint: Choose, arbitrarily, input resistor, R1 = 100kN and find feedback resistor, Rf. Since phase is of no concern and the required voltage gain is greater than 1, we can use either an inverting or noninverting amplifier. Answers: Rf (inverting) = 400 k2, Rf (noninverting) = 150 k2 %3D

Exercise In a certain application, a signal source having 60 kl of source impedance, Rs, produces a 1 V,ms signal. This signal must be amplified to 2.5 V,rms and drive a 1 kN load. Assuming that the phase of the load voltage is of no concern, design an operational amplifier circuit for the application. Hint: Choose, arbitrarily, input resistor, R1 = 100kN and find feedback resistor, Rf. Since phase is of no concern and the required voltage gain is greater than 1, we can use either an inverting or noninverting amplifier. Answers: Rf (inverting) = 400 k2, Rf (noninverting) = 150 k2 %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve for the common base amplifier Given B= 100, Si=0.7 (voltage drop) Find a) Avs b) Ais c). What are Ac voltage at each point indicated (A,B,C,D,E) in the circuit with Vs = 100mVp-p
d) Parasitic capacitances usually exist in a practical amplifier. Comment on the possible sources of the parasitic capacitances. How they are likely to affect the frequency response of the amplifier.
You are tasked with designing a linear amplifier using an NPN BJT for the circuit shown below. This means the transistor iv curves apply here. The voltages given are Vcc = 14 V and Vs = 1.0 V. The datasheet for the transistor says VBE (ON) = 0.7 V,VCE (SAT) = 0.2 V, and ß = 400. The design should have ic = 12 mA and VCE = 8 V. Find the resistances Rb and Rc that give the required ic and VCE. Vs H Rb M d VBE Rc VCE Vcc
this is CC(common collecter ) amplifier.why it is a cc circuit, you can get the answer from its AC circuit.so now PLS draw its AC and DC circuit. plz solve it early
4. Is it possible to get a gain less than unity using a non-inverting amplifier configuration? If yes, sketch a circuit.
3- A microwave amplifier for cellular applications is being tested for linearity. The input to the amplifier is the sum of two sinusoidal waveforms at the frequencies of 860 MHz and 870 MHz, with an input power spectrum that looks like the figure on the left below. It is determined that the output power spectrum looks like the figure shown on the right (other components are filtered out). a) What is the value of the linear power gain of the amplifier? b) What is the value of the output IP3 for this amplifier? c) What is the value of the input IP3 for this amplifier? d) What is the max linear (fundamental) output power that can be obtained (in each of the two equal amplitude sinusoids) to keep the third order intermodulation products at a power level of 40 dB below the linear output power? e) What is the max. input power than can be used? -50 dBm -25 dBm output input -60 dBm 850 860 870 880 frequency 850 860 870 880 frequency
For the BJT circuit shown below, sketch the hybrid equivalent model circuit with labels of voltages, impedances, and currents. ... 1.8k0 Vo 39ka 22ko tuF-POL 10UF-POL 1200 1uF-POL 2N2221 100mv 1.5KHZ ODeg
2. Derived the formula of output signal to get the equation of Noise?Current gain In the same way, when power gain is calculated using current instead of power, making the substitution , the formula is: 3. In many cases, the input and output impedances are equal, so the above equation can be simplified to: 4. This simplified formula is used to calculate a current gain in decibels and is equivalent to the power gain only if the impedances at input and output are equal. 5. The "current gain" of a bipolar transistor, or , is normally given as a dimensionless number, the ratio of to (or slope of the -versus- graph, for ). An amplifier has an input impedance of 50 ohms and drives a load of 50 ohms. When its input () is 1 volt, its output () is 10 volts. What is its voltage and power gain? 8. Voltage gain is simply? 9. The units V/V are optional but make it clear that this figure is a voltage gain and not a power gain. Using the expression for power, P = V:/R, the power gain is? 10. The…
Figure 2 shows a typical BJT amplifier, with its parasitic capacitances displayed. The current gain of the transistor is B=150 and the voltage gain of the amplifier is Am =-125. The small signal resistances of the transistor are re =16 ohm and r0 = infinity, respectively. The values of resistors and capacitors in the figure are: R1 =80 kohm, R2 =20 Kohm, Rc = 2 Kohm, RE = 2 Kohm, Rs =50 W, RI=5 kohm, Cs=2 uF, Cc=2 uF, Ce =10 uF, Cbc =4 pF, Cbe = 10 pF, Cce =1 pF, Cwi = 4 pF, CWO = 9 pF, and Vcc = 20 V. a) Sketch a simplified circuit diagram of Figure 2 for high frequency analysis. b) Using the concept of "Miller effect capacitance", calculate the input and Output Miller effect capacitances of Figure 2, respectively. C) Determine the upper cut-off frequency of Figure 2 that is imposed by its input network only. d) Explain briefly the possible ways to increase the upper cut-off frequencv of this amplifier.
Q2. What is PCC in harmonic analysis and why it is important? Explain how the total harmonic distortion and total demand distortion is determined at PCC. Write the expressions of calculate the THD, THD; and TDD.
1. Given a circuit in figure 1.1 where an amplifier model is proposed. The input signal is a courant source with values provided in the figure. 1.1 Calculate the expression T(jw) = Vo(jw) is(jw) * 1.2 If the input frequency win = 10 rad/s, evaluate the value of T(jw) and use the obtained results to determine the equation for the output voltage Vo(t) when Is = 2mA · sin [ 10 t] 20Ω + Ro + 10µF RLS Vo i 5000 is (1 R;S Vi 100 v 1kQ Is = 2mA · sin [Wint ] Figure 1.1 Amplifier circuit