Exercise 4-7: A 555 timer configured to run in the astable mode (oscillator) is shown in Fig. 4-38. Determine the frequency of the output and the duty cycle. [Answers: 5.64 kHz, 59.5%] +5.5 V R₁ · 2.2 ΚΩ Vcc R₂ • 4,7 ΚΩ Cent 0.022 μF RESET DISCH TIRESII TRIG 555 OUT CONT GND Fig. 4-38 C₁ 0.01 μF

Exercise 4-7: A 555 timer configured to run in the astable mode (oscillator) is shown in Fig. 4-38. Determine the frequency of the output and the duty cycle. [Answers: 5.64 kHz, 59.5%] +5.5 V R₁ · 2.2 ΚΩ Vcc R₂ • 4,7 ΚΩ Cent 0.022 μF RESET DISCH TIRESII TRIG 555 OUT CONT GND Fig. 4-38 C₁ 0.01 μF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1920 [Q5B] The signal m(t) (whose spectrum is shown in the figure below) is sampled at a rate of 15k samples per second. Let A = 2kHz. (a) What is the maximum value for the frequency B to ensure proper ideal sampling? (b) Draw the spectrum of the sampled signal when B = 5kHz. M(f) 1P+ -B -A 2 0 A B
Calculate the frequency of oscillation for the wen-bridge oscillator in kHz
Please refer to the attached image for the question, and then design according to the requirments given, thanks.
Determine the astable frequency and duty cycle of the 555 timer circuit below
Please solve colpitts oscillator why does the output change when the inductor value is changed.
The rectifier above drives a 950-Ω load with a peak voltage of 3.15V. For a 100-μF smoothing capacitor, calculate the ripple amplitude if the frequency is 50 Hz. (Assume VD,on = 0.75 V)
For the Phase-Shift oscillator, determine the oscillator frequency C, = C2 = C3 = C = 0.001 µF R2 = R3 = R = 10 k. R1 = R/2 = 5 kQ ... Ry C C3 OV OV R R2 A 2.32 kHz B) 5.67 kHz 7.8 kHz D) 8.5 kHz
Determine the range values of the external resistors for a 555 timer used as an astable multivibrator with an output frequency of 10 kHz. if the external capacitor C is 0.01 μF and the duty cycle ranges between 50% to 75%. Draw the circuit of the multivibrator.
The simple diagram of the diode circuit and the negative square wave input are shown in the figure. What will be the output voltage value after the tenth cycle? ( Vi=18V , C1=µF, C2= 47 µF 3.83 V (Approximation will be made by assuming C2 large C1)
the correct name of this oscillator is * R1 Tank Circuit crystal RC LC Hartley K Feedback 2 ww www R3 R4 ww +V v Output Ov
What is the output voltage(R1) on the 1st half cycle? C1 D1 R1 )20v V1 SV
Vin + D₁ K C₁RL + Vout The rectifier above drives a 950-2 load with a peak voltage of 3.15V. For a 100-µF smoothing capacitor, calculate the ripple amplitude if the frequency is 50 Hz. (Assume VD,on = 0.75 V)