Exercise 2:Transform each the following instructions into R or I format and inBinary code$s0 - $s7 : registers 16 - 23S10 - $17 : registers 8- 15$t8 – $19 : registers 24-251- Iw $t0, 0($t1)2- Add $t0, $s1, $s23- Sub $t0, $s3, $s44- Sw $3, 32($s4)5- And $12, $s0, $s7

Answered: Image /qna-images/answer/f5235c43-e9c8-42f7-b3d1-d74e2418fe98.jpg

Answered: Exercise 2: Transform each th Binary…

Engineering

Computer Science

Exercise 2: Transform each th Binary code

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

in ASM (Irvine 32) write a code that solves R = (A % B) % (C % D). Note that ABC are 8 bit signed integers and % is the operator modulo which holds the division operation remainder.
ASAP
Problem: You have the table below of values of telemetry from the satellite. The temperatures are encoded linearly in unsigned binary bytes as a function of time. The samples come in every five minutes starting at time = 0. The temperatures are in degC and the temperature of -50 degC corresponds to a telemetry value of 0, while a temperature of 100 degC corresponds to a telemetry value of 255. (All values are decimal unless explicitly stated otherwise.) Write down the equation that describes the temperature as a function of telemetry value in the form of T = a* TV + b. What is the value of a? What is the value of b? After your data has been downlinked, as shown in the table below, fill in the Time and Temperature columns (to one place past the decimal point for the Temperature). Sample Telemetry value Time (minutes) Temperature (degC) 1 2 3 4 5 6 7 8 9 10 11 12 13 10 12 14 17 21 41 81 181 210 220 215 222 225 0 5 10 60 -44.1 -42.9 -41.8 82.3
6. Using only the binary shift left operation, how can one multiply a number by decimal 16?
Construct binary self-dual code of length 4 and 8.
Generate (7, 4) Hamming code for the binary data ‘1011’. Also, write the gray code representation for the same binary data ‘1011’
Q10/ G(A,B,C,D,E,F)={(2,3,5,7,22,23,32,33,34, 35,37,39,52,53,54,55)+ dz(8,9,10,11,16,17,18,19,60,61,62,63) Select 4-varabe only and rewrite the term in binary with respect to the other two variable, the function G will :be G(A,B,C,D) =Σm (8,1 1 ) +Σd (4,1 0,1 5) +ΣΕ(0,1 ) +Σ F(5,9) G(A,B,C,D) =Σm (8,1 3) + Σd (2,4,1 5)+ΣΕ(0,5) + ΣF (. 1,9) G(AB,C,D) =Σm(11,9)+Σd (10,4,1 5) +ΣΕ (1,5)+Σ F(0,8) G(A,B,C,D) =Σm (1 2,9) +Σd (5,8,1 5) +ΣΕ(2,10)+Σ F(3,11) None of them O
Question 5: Based on the for 32-bit division hardware diagram shown in the next page. Perform the division for 4 bits unsigned integers. Where the dividend is 1011 and the divisor is 0010. Write the division table, with header steps, action, quotient, divisor, and remainder. Divisor 64-DRALU Remainder 64 bits Shift right 64 bits While Control best Quotient Shill left Convert the dividend, divisor, and the calculated results in question (5-1) to decimal to verify your results. Consider the number -1.36875 x 10¹ as the dividend and 5.625 x 10¹ as the divisor. Find their binary representation. Put the results that you got it in question (5-3) in the 8-bit quarter-precision format (1 for sign bit, 2 for exponent, and 5 for fraction) 1. floating-point number. Use the IEEE 754 standard. 2. signed integer. e. Show all the steps of the division to results that you got it in question (5-4). Indicate if there is overflow or underflow by assuming that there is a guard bit, a round bit, and a…
Q/write aprogram to convert the following into assembly code, note that all imput ave iba bit numbers R₁ = x ² y R₂ = Z* K R3 = R₁+R₂